Abstract:NiAl base eutectic alloy is an attractive material and promising to use in high temperature environment. However, the inadequate high temperature strength limits its application. In order to improve its strength, Zr was added in the Ti and Hf doped NiAl/Cr(Mo) base eutectic alloys and the effect of Zr addition on microstructure and mechanical properties of the eutectic alloy was investigated in this work. The results show that small addition of Zr can refine the NiAl/Cr(Mo) lamella inside the eutectic cell and optimize NiAl and Cr(Mo) phase morphology in the intercellular zone. Moreover, the Zr addition promotes the precipitation of bulk Heusler phase along eutectic cell boundary. With the increase of Zr addition, the eutectic cell of the alloys becomes fine, but the NiAl and Cr(Mo) phases in the intercellular zone become coarse and the Heusler phases exhibits semi-continuously distribution along the eutectic cell boundary. When the Zr content increases to 1% (atomic fraction), the NiAl and Cr(Mo) phases in eutectic cell and intercellular zone are all coarsened obviously. Additionally, coarse Cr-rich phases precipitate in the intercellular zone and Heusler phase forms the continuous network along eutectic cell boundary. The addition of Zr promotes the precipitation of coarse beta-NiAl and alpha-Cr phase in Cr(Mo) phase and NiAl phases, respectively. Moreover, the segregation of Heusler phase forming elements along the precipitate interface leads to the formation of a large number of interfacial dislocations. In addition, the addition of Zr results in the precipitation of fine Heusler particles in NiAl phase. It is shown that appropriate addition of Zr can improve the compression strength of Ni-33Al-28Cr-5.5Mo-1.0Ti-0.3Hf eutectic alloys significantly at room temperature and high temperature without reducing its compression plasticity, but more addition of Zr reduces the compressive plastic of the alloy inevitably.

Formation Mechanism of Ternary NiAl-Mo Eutectic Alloy under Quenching Condition

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

The formation mechanism of eutectic microstructures in NiAl-Cr composites

Effect of Growth Rate on the Tensile Properties of DS NiAl/Cr(Mo) Eutectic Alloy Produced by Liquid Metal Cooling Technique

Strong cooperation growth of two phases in the ternary eutectic

Phase-Field Simulation of the Microstructure Evolution in the Eutectic Alloy NiAl-31Cr-3Mo

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Ternary eutectic growth and associated tensile properties of directionally solidified Al87Si11Ni2 alloy

Nanocrystallization Kinetics of Amorphous Fe73.5Cu1Nb3−xMoxSi13.5B9 (x=1, 2, 3) Alloys

Experimental study on phase relations in the Al-Mo-Nb ternary system

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

Design and Characterization of a Novel NiAl‐(Cr,Mo) Eutectic Alloy

Spinodal Decomposition of B2‐phase and Formation of Cr‐Rich Nano‐precipitates in AlCoCrFeNi2.1 Eutectic High‐Entropy Alloy

Stabilization of the Ternary Eutectic Growth in Additively Manufactured AlNiCe Alloys

Effects of solidification kinetics on phase selection of Ni–Al alloys

Microstructure evolution behavior of Ni3Al (γ′) phase in eutectic γ-γ′ of Ni3Al-based alloy

Design Multicomponent Eutectic Alloys in the Co–Cr–Fe–Ni–Nb System Using Simple Mixing Method

EFFECT OF Zr ADDITION ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF NiAl/Cr(Mo)BASE EUTECTIC ALLOY

Microstructure and Mechanical Properties of Rapidly Solidified NiAl–Cr(Mo) Eutectic Alloy Doped with Trace Dy

Rapid Dendritic Growth and Solute Trapping Within Undercooled Ternary Ni-5%Cu-5%Mo Alloy

A comparative study of iron, cobalt or cerium micro-alloying on microstructure and apparent viscosity of Al-5Ni alloy