Abstract:Purpose: To investigate the resistance to fracture of three crown and core combinations, made with different core build-up systems on human teeth, using a standardized test method. Materials and methods: The anatomic crowns were removed from six groups (n = 8) of endodontically treated, human premolars in conformity with a brass master dye, using the Celay duplicating device. Three of these groups were provided with a core build-up with-out an endodontic post (Ti-Core, Photo-Core and Ketac-Molar); two other groups were provided with a core build-up with an endodontic post (a cast post and core, and a composite with a silica post), and one group was not provided with a core. All groups were then prepared in conformity with a master dye. This preparation ended in axial dentin, 2 mm apical from the core build-up. Thus in the sixth group (premolars without a core build-up), this preparation only affected the 2 mm axial dentin (ferrule), which resulted in a small retention area (2 mm axial dentine) for the crown. Finally, a standard crown was cemented and 24 hrs afterwards loaded until fracture in an Instron testing machine at an angle of 45 degrees. For comparison with the standardized procedures, a seventh group (Photo-core without post) was prepared manually, with dimensions similar to the standardized groups. Results: Within the standardized test set-up no significant difference in strength between the 6 groups could be demonstrated. Only in the case of the hand-made Photo-Core and the cast core was the fracture load significantly different (P= 0.01). In addition, this hand-made group displayed a larger standard deviation than the standardized groups. Taking into consideration the fact that the maximum bite force in the bicuspid region is about 580 N, these tests showed that within the limitations of the standardized test set-up, where the samples had no history of fatiguing, a core build-up without a post is an alternative for the conventional cast core. In this study, the fabrication of the standardized samples proved to be accurate, fast and economical. This method also enables the evaluation of the performance of core and crown design combinations in relationship to the amount of remaining tooth structure by using different master dies and, moreover, to reduce the high standard deviation in this kind of research.

Effects of post length on horizontal load of post-core system]

Influence of luting agents on fracture resistance of endodontically treated incisors with metal posts

Clinical effects of defected posterior teeth restored by 3 cast post-cores

Development of dental posts by carbon fiber reinforced resin

In Vitro Effect of the Length of Relocated Cervical Margin with Casting Post and Core, Prefabricated Fiber Post, and Polyethylene Fiber with a Composite Core on Fracture Resistance and Marginal Integrity

Investigation of Material Properties of One-Piece Glass Fiber Post-and-Core Affecting Biomechanical Responses of the Restorative System

The effect of different posts on fracture strength of roots with vertical fracture and re-attached fragments

In-vitro study of the fracture load of CAD/CAM one-piece glass fiber post-and-core

Influence of glass fibre post length and remaining dentine thickness on the fracture resistance of root filled teeth

Influence of the type of post and core on in vitro marginal continuity, fracture resistance, and fracture mode of lithia disilicate-based all-ceramic crowns

[Fatigue and Fracture Resistance of the Flared Roots Restored with Computer Aided Design and Computer Aided Manufacturing Glass Fiber Posts].

The three-dimension finite element analysis on mandibular first molar restored with different designed fiber post-core and all ceramic crown

Exploring fiberglass post numbers for enhanced fatigue resistance in molars without coronary remnants

Effects of 3 different residual root treatments after post-and-core restoration: An in vitro fracture resistance experiment and finite element analysis

Biomechanical Analysis of One-Piece Post and Cores in Different Materials: Can High-Performance Polymers Be an Option?

Three-dimensional finite element analysis of effect of root canal taper and post on tooth stress distribution]

[An Experimental Study on Fracture Resistance of Metal-Ceramic Crowned Incisors with Different Post-Core Systems].

[In vitro fracture behaviour of composite crowns with and without posts]

Influence of fiber post on endodontically-treated molars restored with resin-based composite：a finite element analysis

Fracture strength of different core build-up designs

Fracture Resistance of Crowned Incisors with Different Post Systems and Luting Agents