Abstract:Carbide coatings are very important in molding industries due to their good anti-wear properties increasing the life of molds of hot and cold forging, extrusion and powder metallurgy exposing to abrasive forces. Diverse processes are applied to produce carbide coatings. One of them is the thermo-reactive diffusion method (TRD) using a molten salt bath. This process has many advantages including cost-effectiveness over other similar surface coating methods. The aim of this study is the formation of carbide-composite coatings using molten salt baths containing oxides of carbide forming elements individually and in a mixed form on SKD-11 cold work tool steel at 1000 degrees C. For this purpose, two sets of experiments were considered in this study. In experiment A, a chromium oxide bath and then a mixed chromium oxide and vanadium oxide bath with a molar ratio of Cr to V equal to 0.66 were used. In experiment B, at first a mixed chromium oxide and vanadium oxide bath (Cr/V ratio = 0.66) and next a single bath of vanadium oxide were utilized. To evaluate and compare the produced coatings, FE-SEM, EPMA (point, line and map), XRD analysis, nano-indentation and wear tests were performed. The results showed that the coatings include chromium carbides (Cr3C2, Cr7C3 and Cr23C6) and vanadium carbides (V2C, V6C5 and V8C7) as well as a carbon-chromium-vanadium triple phase with the composition of Cr2C2V. Moreover, the best hardness and abrasion resistance were gained for the coating produced in the molten bath containing chromium oxide and vanadium oxide after experiencing a chromium oxide bath. For the sample, the hardness was between 17.2 and 19.6 GPa and the lowest amount of COF was 0.32.

STUDY ON PREPARATION AND PROPERTIES OF VANADIUM CARBIDE COATING

Microstructure and Properties of Cr12MoV Steel after Salt-bath Vanadizing

On the Formation and Properties of Chromium Carbide and Vanadium Carbide Coatings Produced on W1 Tool Steel Through Thermal Reactive Diffusion (TRD)

Effect of Carbon Content and Elements Mo and V on the Microstructure and Properties of Stainless Steel Powder Surfacing Layer

INVESTIGATION OF CHROMIUM AND VANADIUM CARBIDE COATING FORMATION ON SKD11 AND T10 BY THERMO-REACTIVE DIFFUSION (TRD) METHOD

Investigation on preparation of vanadium nitride hard coating by in-situ method technique

Investigation of Chromium and Vanadium Carbide Composite Coatings on CK45 Steel by Thermal Reactive Diffusion

Tribological Properties of Duplex Coatings of Chromium-Vanadium Carbide Produced by Thermo-Reactive Diffusion (TRD)

Grain Size and Adhesion Strength of the V<sub>8</sub>C<sub>7</sub> Coatings Produced <i>In Situ</i>

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

The microstructure evolution of VC coatings on AISI H13 and 9Cr18 steel by thermo-reactive deposition process

Evaluation of Vanadium Carbide Coatings on AISI H13 Obtained by Thermo-Reactive Deposition/diffusion Technique

Characterization of gradient vanadium carbide coating using synchrotron X-ray microdiffraction

Insights into the oxidation resistance mechanism and tribological behaviors of multilayered TiSiN/CrVxN hard coatings

Influence of Cr on the Surface Properties of the Micro-Textured WC+Co Alloy Coating

MICROSTRUCTURE AND WEAR RESISTANCE OF CHROMIUM CARBIDE COATING IN SITU SYNTHESIZED BY VEB

Study on the surface performance strengthening of AlCrN coated cemented carbide by micro-texture laser preparation process

EFFECT OF CrMoN HARD COATINGS WITH DIFFERENT COM-POSITIONS ON THE SURFACE PROPERTIES OF DIE STEELS

Research progress on tantalum carbide coatings oncarbon materials

Study on mechanical properties and corrosion resistance of VC nanoparticles reinforced Ni-W coatings

Microstructure and Formation Mechanism of Vanadium Carbide-Reinforced Iron-Matrix Composites Prepared by Solid-Phase Diffusion