Abstract:Ammonia is now being explored as a potential gas turbine fuel because of its renewable and carbon-free nature. Ammonia combustion possesses various limitations, such as high NO emissions, low burning velocity, and high auto-ignition temperature. Moreover, dual-fuel combustion approaches can be used to mitigate these drawbacks. However, the limitations of available information about the resulting emissions are insufficient to encourage widespread adoption. In this work, an NH 3 /CH 4 -air fueled self-recuperative high aspect ratio annular tubular porous burner is developed for gas turbine power applications. In this burner, an annular zone surrounds the combustion chamber to preheat the incoming air, while two perforated discs are mounted between the combustor and annular zone for uniform distribution of air. Eight Zirconia foams (4 of 10 PPI and 4 of 20 PPI) are stacked at the upstream side of the combustor. Experimentally, air preheat temperature, combustor exit temperature, NO, and CO emissions are analyzed and measured for various ammonia addition (0–41 % by weight) percentages, equivalence ratio of 1.0, and heat inputs of 17 & 21 kW for 10 PPI and a combination of 10 and 20 PPI porous foams. A preheated air stream coming from the annular zone speeds up fuel dissociation and helps in stabilizing the flame on the upstream side of the combustor. Combustor exit temperatures are lower in sandwich cases of 10 + 20 PPI than the porous foams of 10 PPI. However, with porous foams of 10 PPI, the air preheat temperature is higher. The insertion of porous foams shows better recirculation of heat and stable combustion is observed for higher percentages of ammonia and higher thermal inputs. The OH radicals are distributed for larger areas inside the dumb combustor, while for porous combustion, it is distributed near the porous foams. The porous sandwich cases of 10 + 20 PPI shows higher combustion efficiency compared to 10 PPI and without porous cases. The chemical kinetic analysis shows that the HNO and HCO radicals act as the main intermediate channel for NO and CO production.

Kinetics of Ammonia Decomposition in Hot Gas Cleaning

Catalytic Hot Gas Cleaning Of Fuel Gas From An Air-Blown Pressurized Fluidized-Bed Gasifier

Investigation of Ammonia Formation During Gasification in an Air Blown Spouted Bed: the Effect of the Operating Conditions on Ammonia Formation and the Identification of Ways of Minimizing Its Formation

Enhancement of the Ammonia Kinetic Mechanism for Nitrogen-Based Pollutant Chemistry

Kinetic Modeling of the Thermal Decomposition of Ammonia

Kinetics of ammonia decomposition on nickel

Effect of Alkali Vapor Exposure on Ni-Mgo/Gamma-Al2o3/Cordierite Monolithic Catalyst for Biomass Fuel Gas Reforming

Reactivity and kinetics of biomass pyrolysis products for in-situ reduction of NOx in a bubbling fluidized bed

Experimental and Kinetic Study on Laminar Flame Speeds of Ammonia/syngas/air at a High Temperature and Elevated Pressure

Kinetics of catalytic biomass pyrolysis using Ni-based functional materials

Hydrogen and carbon produced by fluidized bed catalytic methane decomposition

An Experimental and Kinetic Modelling Study on the Oxidation of NH3, NH3/H2, NH3/CH4 in a Variable Pressure Laminar Flow Reactor at Engine-Relevant Conditions

Thermal Removal of COD and NH3N from Lurgi Coal‐gasification Wastewater

Study of the ammonia decomposition over iron catalysts

Numerical Modeling of a Coal/Ammonia Co-fired Fluidized Bed: Control and Kinetics Analysis of Nitrogen Oxides Emissions

Experimental and Kinetic Modeling Investigation of NOx Control in Coal Combustion by Ammonia Reburning

Molecular dynamics investigation of the effect of ammonia on coal pyrolysis and the nitrogen transformation

Experimental and computational (Chemical Kinetic + CFD) analyses of Self-Recuperative annular tubular porous burner for NH 3 /CH 4 -air Non-Premixed combustion

Spatially Resolved Measurements in a Stagnation‐Flow Reactor: Kinetics of Catalytic NH3 Decomposition

Improving the NH3 Oxidation and Removing NOx During Ammonia-Rich Fuel Catalytic Combustion Using the Ag/CuOx@SiO2 Catalyst with High-Temperature Catalytic Activity

Preparation of Syngas Via Catalytic Gasification of Biomass with a Nickel-based Catalyst