Abstract:Fusion welding is extensively used for joining structural assemblies, especially those with complex geometries. However, it often results in heat-affected zones (HAZ) that are, in most cases, softer than other regions around and beyond the weld area. Coupling both experiment and thermodynamic modeling—electron microscopy, x-ray microscopy (XRM), and CALculation of PHAse Diagrams (CALPHAD)—we re-examine the origin of softening in tungsten inert gas (TIG)-welded heat-treatable AA 6061-T651 for a more comprehensive understanding of its (softening) evolution. This study reveals material softening up to at least 38 mm away from the weld center, and partitioned heat-affected zones—HAZ1, HAZ2, HAZ3, and HAZ4—based on peak temperature, associated hardness, and precipitate phases in these zones. Analytical modeling and thermodynamic simulation predict solid solution and further precipitation of coherent GP zones in HAZ1, while coarsening of pre-existing precipitate occurs in HAZ2 (non-coherent/stable β -Mg 2 Si), HAZ3 (both semi-coherent/metastable β ′ and coherent/metastable β ′′) and HAZ4 (coherent/metastable β ′′). These welding-induced transformations—origin of softening—result in non-homogenous hardness in the zones compared to the unaffected base material (120 HV): HAZ1 to HAZ4 are 66-72, 54-64, 64-94, and 95-106 HV, respectively. Under tensile load, the TIG-welded sample fractures at the softest region—HAZ2. Additionally, XRM analysis confirms the presence of porosity in the welded area and its closure during plastic deformation, so that the severity of softening has a greater influence on localized fracture than the presence of porosity in the weld area. This work shows that new solid-state welding technologies that minimize nanostructural changes in base materials, especially precipitation-hardened alloys, should be sought.

Microstructural Evolution of 9cr–1mo Deposited Metal Subjected to Weld Heating

Investigation of thermal effects on mechanical properties of 9Cr-1Mo to 9Cr-1Mo welded joints for high-temperature applications

Microstructural evolution of a low-alloy steel / nickel superalloy dissimilar metal weld during post-weld heat treatment

Investigation on the weakest zone in toughness of 9Cr/NiCrMoV dissimilar welded joint and its enhancement

Microstructural evolution and its effect on mechanical properties in different regions of 2219-C10S aluminum alloy TIG-welded joint

Optimizing microstructure and mechanical properties of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy electron beam welded joint through post-weld heat treatment

Temperature-gradient Induced Microstructure Evolution in Heat-Affected Zone of Electron Beam Welded Ti-6Al-4V Titanium Alloy

Postweld Heat Treatment of 15Cr-6Ni-2Mo-1Cu Supermartensitic Stainless Steel Welds

Microstructure evolution of weld root in dissimilar weld metal in S690QL high-strength steel under multiple welding thermal cycles

Analysis on the Microfissuring Behavior in the Heat-affected Zone of Electron-beam Welded Nickel-based Superalloy

Effect of Tempering Heat Treatment on the Microstructure and Impact Toughness of a Ni-Cr-Mo-V Steel Weld Metal

X-ray Microscopic and Thermodynamic Model Assessments of Softening in TIG-Welded AA 6061-T651

Study on Microstructure and Its Evolution of Electron Beam Welded TC4 Joint

Microstructure and Fatigue Behavior of Cr-Mo Steel Weld Joints with Automatic TIG Welding

The Effect of Microstructure and Welding-Induced Plasticity on the Strength of Ni–Mo–Cr Alloy Welds

Improvement in Weldment of Dissimilar 9% CR Heat-Resistant Steels by Post-Weld Heat Treatment

Microstructure transformation and pore formation mechanism of Mo-14Re alloy weld by vacuum electron beam welding

Mechanical Behavior and Failure Mechanism of Q&P980 Steel During In Situ Post-Weld Heat Treatment (PWHT) Resistance Spot Welding

In-situ investigation of microstructure-dependent deformation behavior of an electron-beam welded Ni Co based superalloy

Microstructure Evolution and Mechanical Properties of TA15/Ti60 Tailor Welded Blank by Electron Beam Welding

Thermal Effect of Welding on Mechanical Behavior of High-Strength Steel