Abstract:ObjectivesTo resolve the feasibility of the pulse-delay photocuring technique as a clinical strategy for reducing the detrimental polymerization stress induced in dental composites during the photocuring process.MethodsModel dental composites with high and low-filler contents were cured with the pulse-delay photocuring technique using different combinations of photocuring variables (irradiance, exposure time, and delay time). Irradiance used ranged from 0.1 W/cm2 to 4 W/cm2. The exposure time of the first pulse varied from 0.2 s to 27.2 s and the delay times ranged from 10 s to 120 s. The radiant exposure was varied from 4 J/cm2 to 20 J/cm2. A cantilever-beam based instrument (NIST Standards Reference Instrument 6005) was used to implement the photocuring technique for the measurement of the polymerization properties (the degree of monomer conversion, polymerization stress induced due to shrinkage, and temperature change due to the reaction exotherm and curing light absorbance) simultaneously in real-time. These properties were compared with those obtained using the conventional photocuring technique (i.e., using a constant irradiance for a fixed exposure time, a uniform exposure).ResultsThere exists a minimum radiant exposure, such that a reduction in the polymerization stress can be achieved without sacrificing the degree of monomer conversion by using the pulse-delay over the conventional photocuring technique. More specifically, stress reductions of up to 19% and 32% was observed with the pulse-delay when compared with the conventional photocuring technique at an irradiance of 0.5 W/cm2 and 4 W/cm2, respectively. The reduction occurred when the exposure time of the first pulse was greater than, but closer to, the gelation time (i.e., lower than the vitrification time) of the composite, regardless of the delay time used. Lower thermal shrinkage (contraction) during the post-curing time, rather than the stress relaxation during the delay time or lower degree of monomer conversion as claimed in the literature, is the cause of the reduction in the polymerization stress.SignificanceThe study clarifies a long-standing confusion and controversy on the applicability of the pulse-delay photocuring technique for reducing the polymerization stress and promotes its potential clinical success for dental restorative composites.

Intermittent Curing and Its Effect on Pulsed Laser-Induced Photopolymerization

Simultaneous Measurement of Polymerization Kinetics and Stress Development in Radiation-Cured Coatings: A New Experimental Approach and Relationship between the Degree of Conversion and Stress

Effects of Curing Temperature and Uv Intensity on Electro-Optical Properties of Psct Reverse-Mode Light Shutters

Cure Kinetics of an Epoxy Resin Containing Naphthyl/dicyclopentadiene Moieties and Bis‐phenoxy (3‐hydroxy) Phosphine Oxide System and Properties of Its Cured Polymer

Matrix Method for the Observation of Laser-Induced Photopolymerization with Short Time Curing

Real-Time Characterization for Laser-Induced Photopolymerization

Effect of Macro-Initiator and Curing Time on Electro-Optical Properties of Polymer Dispersed Liquid Crystal

Investigation Of Ir Laser-Induced Photopolymerization Of Multifunctional Acrylate By Real-Time Ftir Spectroscopy.

STUDY ON THE LASER INDUCED PHOTOPOLYMERIZATION INITIATED BY A NOVEL INFRARED INITIATOR

Control of the microstructure of polymer network and effects of the microstructures on light scattering properties of UV-cured polymer-dispersed liquid crystal films

Visualizing Curing Process Inside Polymers

Photoinitiator type and applicability of exposure reciprocity law in filled and unfilled photoactive resins

Micro-hardness Measurement of Photopolymer in Stereolithography.

Laser induced thermal effect on the polymerization behavior in up-conversion particle assisted near-infrared photopolymerization.

Delayed post-curing stage and oxygen inhibition of free-radical polymerization of dimethacrylate resin

Influence of Photoinitiator Type and Curing Conditions on the Photocuring of Soft Polymer Network

Modeling the Optimal Conditions for Improved Efficacy and Crosslink Depth of Photo-Initiated Polymerization

Thermal shrinkage reveals the feasibility of pulse-delay photocuring technique

Thermal Studies of Three-Dimensional Printing Using Pulsed Laser Heating

Heat generation at photopolymerization by multiple-spot exposure with blue light

Dual-Wavelength (UV and Blue) Controlled Photopolymerization Confinement for 3D-Printing: Modeling and Analysis of Measurements