Abstract:Digital light processing (DLP) based vat photopolymerization (VPP) is an additive manufacturing (AM) technology that projects sequential optical masks to selectively cure cross-sectional patterns layer by layer. DLP-VPP is widely used in rapid prototyping and fabrication of diverse products ranging from consumer goods to soft robotics. Degree of curing (DoC) is one primary performance metric for photopolymer-based AM processes due to its high correlation with key material properties such as density and elastic modulus. Yet there is a lack of in-situ monitoring approaches to understand and control the photopolymerization process and part properties. State-of-the-art works use in-situ Fourier-transform Infrared Spectroscopy (FT-IR) and atomic force microscopy, which would interfere with the process and material and can only measure DoC at one single point each time. This work aims to develop a cost-effective, non-interruptive, non-invasive, and full-field in-situ interferometric curing monitoring (ICM) method for revealing the spatiotemporally resolved curing dynamics and material evolution during DLP-VPP. To this end, a physics-based sensor model is derived and machine learning-aided sensor data processing and analytics methods are developed for addressing the unique measurement challenges in DLP-VPP-specific ICM. Using the developed ICM model and methods, the acquired interferogram data is cleaned, classified, and calculated for estimating each voxel's refractive index, which is an indicator of optical density as well as physical density. Then, a DoC prediction model is created by correlating the in-situ ICM-measured refractive index to ex-situ FT-IR-measured DoC. Our experiment results demonstrate that the developed ICM system and methods are capable of measuring the geometry (e.g., lateral dimensions and shapes) of printed part as well as capturing the changes in curing speed, refractive index, and DoC due to the different exposure masks and intensities being used in DLP-VPP. It has the potential to provide real-time multi-modality measurement and enable closed-loop feedback control for enhancing the DLP-VPP process reproducibility and print quality.

Matrix Method for the Observation of Laser-Induced Photopolymerization with Short Time Curing

Real-Time Characterization for Laser-Induced Photopolymerization

Simultaneous Measurement of Polymerization Kinetics and Stress Development in Radiation-Cured Coatings: A New Experimental Approach and Relationship between the Degree of Conversion and Stress

Numerical Simulation on Solvent Diffusion during Polymeric Coating Curing Processes

Intermittent Curing and Its Effect on Pulsed Laser-Induced Photopolymerization

An Analysis of Photopolymerization Kinetics and Stress Development in Multifunctional Acrylate Coatings

Solvent Concentration Distribution in Acetone/PMMA Coating Solution Measured by Laser Confocal Raman Spectroscopy Method

Polymerization Shrinkage of (meth)acrylate Determined by Reflective Laser Beam Scanning

Numerical Simulation of Composite Material Light-Curing Process Based on the Finite Element Analysis Method

[A New Dynamic Approach to Monitoring Dental Composite Curing Kinetics].

Bildbasierte Bestimmung der räumlichen und zeitlichen Verteilung des Brechungsindex während der Aushärtung von Polymeren in der additiven Fertigung von Optiken

Investigation Of Ir Laser-Induced Photopolymerization Of Multifunctional Acrylate By Real-Time Ftir Spectroscopy.

Magnetic Fiber Enabled Curing Electrogram: Real-time Process Monitoring for Thermosetting Polymer Materials

Fiber-optic Composite Cure Sensor: Monitoring the Curing Process of Composite Material Based on Intensity Modulation

Experimental Investigation of Polymeric Material Removal by Low Diffraction Laser Beam

Applicability of the Focusing Method to Measure the Refractive Index Profile of Polymer Optical Fibers

Method for Obtaining Light Curing Printing Condition Based on New Theoretical Description

Study of composite cure real time sensing using fiber optic sensor

An Investigation of a Fiber Optic Sensor in the Composite Cure Process

Deviation of optical limiting performances from the polymer matrix in the polymer based solid samples

In-situ Interferometric Curing Monitoring for Digital Light Processing based Vat Photopolymerization Additive Manufacturing