Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Synthesis and Characterization of Nanoparticulate Strengthened Nickel Microcomponents

Investigation on nickel/alumina-nanoparticles co-deposition

Electrochemical co-deposition of Nickel-Alumina Nanocomposite for Microsystem Applications

Nanoparticle Reinforced Metal Composites Prepared by Electrocodeposition

Electrodeposition and Mechanical Characterization of Ni-carbon Nanotubes Composite Coatings

Microstructure and Mechanical Properties of ABOw and Nickel-Coated MWCNTs Reinforced 2024al Hybrid Composite Fabricated by Squeeze Casting

Fabrication of Ni-Al2o3 Composite Microcomponent by Electroforming

Fabrication and Characterization of Nickel Nanowire Polymer Composites

Nanoparticulate Dispersion, Microstructure Refinement and Strengthening Mechanisms in Ni-coated SiCp/Al-Cu Nanocomposites

Sediment co-deposition of nanostructured Ni-Al2O3 composite coatings

High Strength and High Ductility in Nickel Matrix Nanocomposites Reinforced by Carbon Nanotubes and Onion-Like-carbon Hybrid Reinforcements

Preparation and characterization of nickel nano-Al2O3 composite coatings by sediment co-deposition

Ni composites reinforced with ultrafine and uniform TiCx and Cr3C2 particles in situ: Enhanced properties and a well-matched interface

Ni-Al2O3 and Ni-Al composite high-aspect-ratio microstructures

Fabrication and Characterization of Ni-Al2o3 Nano-Composite Coatings by Sediment Co-Deposition

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Effect of nickel content on the sintering behavior, mechanical and dielectric properties of Al2O3/Ni composites from coated powders

Microstructure and Tensile Properties of Ni Nano Particles Modified MXene Reinforced Copper Matrix Composites

Influence of dispersion methods on nano-Al 2O 3/Ni+Co composite coating by electrodeposition

Influence of Dispersion Methods on Nano-Al<sub>2</sub>O<sub>3</sub>/Ni+Co Composite Coating by Electrodeposition