Abstract:The preparation and tribological properties of PAI/PI‐EPN polymer coatings. To improve the tribological properties of polar crane copper alloy bearings to withstand wear under dry sliding wear and grease lubrication at low temperatures, three kinds of coating materials modified by incorporating WS2 and SiC into polyamide‐imide/polyimide‐phenolic epoxy resin were designed. These composite coatings were sprayed on the surfaces of CuPb22.5Sn2.5 copper alloys by liquid spraying technique. Firstly, the tribological experiments were performed with three different coatings. Then, nanoindentation testing and wear morphology analysis were conducted. The results show that the hardness of the composite coatings decreases with the increase of WS2. As the content of WS2 increases, the coefficients of friction (CoFs) of coatings decreases under dry sliding wear. The S2 coating filled with 7.5 wt% WS2 exhibits the lowest wear rate and the best wear resistance under low temperature and dry sliding wear. The coatings form a lubricating film on the worn surface under dry sliding wear at −70°C, improving the wear resistance of the coatings. The primary wear mechanisms are adhesive wear and fatigue wear. The wear rates of the coatings increase with the increasing content of WS2 under low‐temperature grease lubrication. The S1 coating filled with 5.0 wt% WS2 exhibits the lowest wear. The S1 coating demonstrates a CoF of 0.07 and a wear rate of 6.5 × 10−6 mm3N−1 m−1 at 0°C, showing excellent friction‐reducing and wear‐resistant properties. The primary wear mechanism is adhesive wear. The wear mechanisms of polymer coatings are closely related to temperature. The dominant wear mechanisms transfer from abrasive wear to adhesive wear and fatigue wear under dry sliding wear and decreasing temperature. The wear mechanisms transfer from predominantly adhesive and abrasive wear to adhesive wear, fatigue wear, and abrasive wear under grease lubrication. The hardness of the coatings and the behavior of the polymer at various low temperatures are the primary factors that affect the differing wear mechanisms.

Study on PPENK/SiC/Si_3N_4 Heat Resistant Anti-Wearing Nano-Composite Coating

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Development of PPESK Heat Resistant,Self-Lubrication and Wear-Resistant Coating

Preparation of Ni-P-SiC Electroless Composite Coating with High Wear and Corrosion Resistance

A Research on the Friction and Wear Properties of Electroless Ni-P Composite Coating

High Temperature Tribological Behavior of Electroless Plating Ni-P-Si3N4-WS2 Composite Coatings

The friction and wear of electroless Ni–P matrix with PTFE and/or SiC particles composite

Effect of SiC Contents on Wear Resistance Performance of Electro-Codeposited Ni-SiC Composite Coatings

Structures and Tribological Performances of PEEK (Poly-Ether-ether-ketone)-based Coatings Designed for Tribological Application

Preparation and Properties of Ni–Co–P/nano‐sized Si3N4 Electroless Composite Coatings

Tribological Properties of Polyimide Coatings Filled with PTFE and Surface‐modified Nano‐si3n4

Study on Preparation and Properties of Nano Ni-SiC Amorphous Composite Coatings

Structure and Wear Properties of Nano-Silicon Dioxide Modified Polyacrylate Composites

Tribological properties of PEEK-based composite coating prepared by thermal spraying

Fabrication and Performance of Ni-Co-P/Si<sub>3</sub>N<sub>4</sub> Electroplated Composite Coatings on Al-Si Alloys

A study on friction and wear characteristics of nanometer Al2O3 /PEEK composites under the dry sliding condition

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Friction and wear behavior of Ni-P-carbon nanotubes (CNTs) electroless composite coating

Friction and Wear of Electroless Ni-P-CS Composite Coating

Study on Friction and Wear Behavior of Polyphenylene Sulfide Composites Reinforced by Short Carbon Fibers and Sub-Micro TiO2 Particles

The investigation of tribological properties of PAI/PI‐EPN polymer coating filled with WS2 and SiC at low temperatures