Abstract:In this research, a linear low density polyethylene (LLDPE) was first melt blended with a series of high density polyethylenes (HDPE) with different molecular weights at a fixed ratio of LLDPE/HDPE=90/10 (w/w). The prepared HDPE/LLDPE blends were then injection-molded into specimen bars through a dynamic packing injection molding (DPIM) technique, in which an oscillating shear field was imposed on the melt by two pistons that move reversibly with the same frequency during the packing stage. The crystal morphology, orientation and tensile properties were characterized by scanning electron microscopy, two-dimensional wide-angle X-ray scattering and Instron, respectively. Compared with conventional injection molding, DPIM caused an obvious increase in tensile strength in the injection-molded bars. Interestingly, LLDPE blended with low molecular weight HDPE (LMW-PE) was found to possess much higher tensile strength than that blended with high molecular weight HDPE (HMW-PE). Shish–kebab morphology was observed for all blends obtained, regardless of the molecular weight of the HDPE. However, thicker but shorter lamellae were observed for the LLDPE/LMW-PE blend, corresponding to a higher melting temperature; while thinner but longer lamellae were seen for the LLDPE/HMW-PE blend, corresponding to a lower melting temperature. Furthermore, the phase miscibility between HDPE and LLDPE was found to increase with increasing HDPE molecular weight, which would affect the sensitivity of molecular chains for response to external shear. The changed miscibility, together with the changed entanglement density in different HDPE was responsible for the change in tensile strength and unique crystal morphology of LLDPE induced by adding HDPE.

Ultrasonic improvement of rheological and processing behaviour of LLDPE during extrusion

Effect of Oscillatory Shear on the Mechanical Properties and Crystalline Morphology of Linear Low Density Polyethylene

Effect of Superimposed Oscillatory Shear on Crystalline Behavior and Mechanical Properties of PE-LLD

Study on Metal Forming Patterns of the Ultrasonic Vibration Assisted Upset-extruding Process

Physical and chemical effects of ultrasound vibration on polymer melt in extrusion

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Surface and volume effects in multimodal ultrasonic vibration assisted micro-extrusion forming: Experiments and modelling

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Preparation and characterization of long-chain branched HDPE by UV-induced reactive extrusion at mild temperature

Research on enzyme pretreatment of polylactic acid/cotton blended fabric under ultrasonic wave

A Study of Ultraviolet Irradiation Functionalization of LLDPE and Its Modification of PA66

Improving the rheology of linear low-density polyethylene (LLDPE) and processability of blown film extrusion using a new binary processing aid

Ultrasonic effects on molecular weight degradation, physicochemical and rheological properties of pectin extracted from Premna microphylla Turcz

Elongational Flow Field Processed Ultrahigh Molecular Weight Polyethylene/Polypropylene Blends with Distinct Interlayer Phase for Enhanced Tribological Properties

A Study of LLDPE Functionalized Through Ultraviolet Irradiation and Interfacial Interaction of PA66/functionalized LLDPE Blends

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Enhancing Chain Mobility of Ultrahigh Molecular Weight Polyethylene by Regulating Residence Time under a Consecutive Elongational Flow for Improved Processability

Studies on Linear Low-Density Polyethylene Functionalized by Ultraviolet Irradiation and Its Compatibilization

Unique crystal morphology and tensile properties of injection-molded bar of LLDPE by adding HDPE with different molecular weights

In-line rheo-optical characterization of PET hydrolysis and chain extension during extrusion

Ultrasonic controlling of degradation of polymer materials