Abstract:In this study, a C-9(+) fraction of saturate-rich Tertiary source rock-derived oil from the South China Sea basin was pyrolyzed in normal and supercritical water using a 25 mL vessel at a range of temperature from 350 to 425 degrees C for 24 h, to probe pressure effects up to 900 bar on gas yields and their stable carbon isotopic compositions during thermal cracking. Pressure generally retards oil cracking, as evidenced by reduced gas yields, but the trends depend upon the level of thermal evolution. In the early stages of cracking (350 and 373 degrees C, equivalent vitrinite reflectance of < similar to 1.1 % R-0), the suppression effect increases with pressure from 200 to 900 bar, but it is most marked between 200 and 470 bar. At the later stages in the wet gas window (390, 405, and 425 degrees C, equivalent vitrinite reflectance of >1.3% R-0), pressure still has a strong suppression effect from 200 to 470 bar, which then levels off or is reversed as the pressure is increased further to 750 and 900 bar. Interestingly, the stable carbon isotopic composition of the generated methane becomes enriched in C-13 as the pressure increases from 200 to 900 bar. A maximum fractionation effect of similar to 3 parts per thousand is observed over this pressure range. Due to pressure retardation, the isotopically heaviest methane signature does not coincide with the maximum gas yield, contrary to what might be expected. In contrast, pressure has little effect on ethane, propane, and butane carbon isotope ratios, which show a maximum variation of similar to 1 parts per thousand. The results suggest that the rates of methane-forming reactions affected by pressure control methane carbon isotope fractionation. Based on distinctive carbon isotope patterns of methane and wet gases from pressurized oil cracking, a conceptual model using "natural gas plot" is constructed to identify pressure effect on in situ oil cracking providing other factors excluded. The transition in going from dry conditions to normal and supercritical water does not have a significant effect on oil-cracking reactions as evidenced by gold bag hydrous and anhydrous pyrolysis results at the same temperatures as used in the pressure vessel.

Hydrothermal Cracking of Polyethylene, Polypropylene, And/or Polystyrene Mixtures under Supercritical Water Condition

Cracking of Polyethylene, Polypropylene, and Polystyrene with Supercritical Water

Catalytic thermal cracking of mixtures of bamboo waste and polypropylene

Experimental analysis on products distribution, characterization and mechanism of waste polypropylene (PP) and polyethylene terephthalate (PET) degradation in sub-/supercritical water

Hydrothermal Liquefaction of Polycarbonate (PC) Plastics in Sub-/Supercritical Water and Reaction Pathway Exploration

Pyrolysis Characterization and Mechanism Studies of Different Structural Plastics: A Comparative Study at Optimal Temperatures

Thermal cracking of oil under water pressure up to 900 bar at high thermal maturities. 1, gas compositions and carbon isotopes

Experimental Investigation on Liquefaction of Plastic Waste to Oil in Supercritical Water.

Study on Pyrolysis Characteristics and Kinetics of Mixed Plastic Waste

Co-pyrolysis of Residual Oil and Polyethylene in Sub- and Supercritical Water

Catalytic Cracking of Polystyrene and Low-Density Polyethylene over Synthesized Zeolite Na-A with Optimized Crystallinity

Hydrothermal Liquefaction of Plastics: a survey of the effect of reaction conditions on the reaction efficiency.

Resource utilization of thermoplastics in supercritical water

Study of the Viscosity and Thermal Characteristics of Polyolefins/Solvent Mixtures: Applications for Plastic Pyrolysis

Experimental Investigation on Gasification Characteristics of Plastic Wastes in Supercritical Water

EFFECT OF DIFFERENT SUPERCRITICAL SOLVENTS ON THE DEGRADATION OF POLYSTYRENE

Unraveling the Role of Mesoporosity and Acidity of Hierarchical Aggregated HZSM-5 in HDPE Vapor Catalytic Cracking for Value-Added Hydrocarbons

Study on the pyrolysis behaviors of mixed waste plastics

Production of low molecular oil from typical polyolefin plastics through molten salts thermal treatment

Hydrothermal liquefaction of diverse plastics using water and seawater

Hydrothermal co-liquefaction of synthetic polymers and Miscanthus Giganteus; synergistic and antagonistic effects