Abstract:The early stage co-pyrolysis of typical plastic waste including polyethylene (PE), polypropylene (PP) and polystyrene (PS) were investigated by using the reactive force field molecular dynamics (ReaxFF MD) simulation with an automatic reaction mechanism analysis software (AutoRMA); the kinetic model, product yields and reaction process of co-pyrolysis were analyzed at atomic level. The results show that the kinetic parameters of PE/PP/PS co-pyrolysis can be obtained through the weighted sum of the parameters for the fracture of C–C and C–H bonds; the estimated activation energy is very close to the experimental one with a small error of ±3.86%, indicating that the fracture of C–C and C–H bonds can accurately characterize the co-pyrolysis process. For the co-pyrolysis of PE-PP mixture, an increase of PP content can improve the yields of oil and combustible gas, whereas for the co-pyrolysis of PP-PS mixture, the increase of PS content can improve the yields of tar and oil. In contrast, for the co-pyrolysis of PE-PP-PS mixture, a higher temperature is beneficial for the conversion of heavy oil into light oil; the light oil content increases from 44.77% at 2400 K to 56.18% at 3000 K. In addition, as a higher temperature can promote the further cracking of light hydrocarbons into gas products of smaller molecules, the yields of H2 and CH4 increase significantly with the increase of pyrolysis temperature, whereas the yields of C2H4 and C3H6 increase first and then decrease with the temperature. In comparison with the separated pyrolysis, the co-pyrolysis commences later, but displays shorter time to reach the first equilibrium state and generates products with smaller molecules. For the separate pyrolysis of PE and PP, their monomers emerge first, hereafter the alkanes and small molecule gases are produced; for the co-pyrolysis process, in contrast, the alkanes and small molecule gases are generated prior to the monomers. Moreover, PS tends to provide ·H radicals in the co-pyrolysis process, which can combine with the free radicals generated from PE and PP pyrolysis, forming small molecule alkanes and H2.

Study on Pyrolysis Characteristics and Kinetics of Mixed Plastic Waste

Study on the pyrolysis behaviors of mixed waste plastics

Pyrolysis of Mixed Plastic Waste: I. Kinetic Study

Investigating Kinetic Behavior and Reaction Mechanism on Autothermal Pyrolysis of Polyethylene Plastic

Kinetic studies on the pyrolysis of plastic waste using a combination of model-fitting and model-free methods

Copyrolysis Characteristics and Kinetic Analysis of Typical Constituents of Plastic Wastes

Synergistic Effect and Chlorine-Release Behaviors During Co-pyrolysis of LLDPE, PP, and PVC

Comparative Study on the Synergistic Co-Pyrolysis of Plastics and Rubber Waste: Thermal Behavior and Product Distributions

ReaxFF MD Study on the Early Stage Co-Pyrolysis of Mixed PE/PP/PS Plastic Waste

Progress of Research on Chemical Upcycling of Plastic Waste Based on Pyrolysis

Research on Pyrolysis Characteristics of Typical Plastics

Pyrolysis characteristics and kinetic study of mixed pyrolysis of municipal solid waste

Study on the kinetics of catalytic pyrolysis of single and mixed waste plastics by spent FCC catalyst

Thermal Behavior, Kinetics and Gas Evolution Characteristics for the Co-Pyrolysis of Real-World Plastic and Tyre Wastes

Investigation on the Synergistic Effect Between Different Components in Pyrolysis of Paper-Plastic Composite Material

Kinetics, Product Evolution, and Mechanism for the Pyrolysis of Typical Plastic Waste

Co-pyrolysis characteristics of typical components of waste plastics in a falling film pyrolysis reactor

Molecular Dynamics Simulation of Converting Waste Polyethylene (PE) to Chemicals and Fuels under Non-Isothermal and Isothermal Conditions

A Multidimensional Numeric Study on Smoldering-Driven Pyrolysis of Waste Polypropylene

Pyrolysis Process of Mixed Microplastics Using TG-FTIR and TED-GC-MS

A Simplified and Effective Molecular-Level Kinetic Model for Plastic Pyrolysis