Abstract:The strengthening of timber beams with carbon-fibre-reinforced polymers (CFRP) has been widely used in the last decades to enhance the behaviour of historical or new timber structures, usually for bending. While considerable improvement in capacity and ductility is typically achieved, the increase in stiffness was, in many cases, well short of analytical expectations, which tend to overestimate stiffness. This study addresses the problem by investigating the underlying mechanical behaviour using experimental, analytical, and numerical tools on a sample of Norway spruce (Picea abies) beams reinforced with carbon-fibre fabric. In the experimental program, each beam is tested for bending with and without CFRP reinforcement in order to determine specimen-specific stiffness increase on an individual basis. The reinforcement yielded an increase of 27% in capacity, 53% in ultimate displacement, and 133% in compliance, verifying its efficiency. Axial compression tests on an independent sample are also performed to verify modulus of elasticity in compression. Numerical computations based on a beam model and a three-dimensional finite element model are performed with the introduction of separate moduli of elasticity for tension and compression in timber. Inverse computation using the experimental load–deflection curves yielded the moduli and the compression yield stress of timber to provide the best match between tests and simulations. The mean difference of only 6% in stiffness between FEM and the tests is obtained. The dominance of normal stresses in the longitudinal direction is found, in correspondence with the experimentally observed tensile failure of timber (apart from a few defected specimens). Compression yield stresses are within 7% (beam model) and 2% (FEM) error compared with the control axial tests. The differences between FE simulations and tests in ultimate load and compliance are within 1%. This study concludes that the application of CFRP in the composite beams enables the determination of timber material properties opposed to pure timber beams without reinforcement, and the adoption of separate moduli of elasticity for tension and compression leads to adequate modelling of reinforced timber beams.

Feasibility Study of Prototype GFRP-Reinforced Wood Railroad Crosstie

PROTOTYPE GRFP-WOOD RAILROAD CROSSTIE: EXPERIMENTAL TESTING AND FINITE ELEMENT MODELING

Modeling And Optimal Design Of Composite-Reinforced Wood Railroad Crosstie

Development Of A Prototype Composite-Reinforced Timber Railroad Crosstie

Experimental Study on Dynamic Behavior of GFRP-to-concrete Interface

FRP-Wood-Concrete Composite Bridge Girders

Performance Characterization of Wood-FRP Bonded Interfaces

Experimental investigation of glued-laminated timber beams with Vectran-FRP reinforcement

Flexural behaviors of GFRP-wood sandwich beams with recycled wood formwork cores

Performance Characterization Of Wood Composites Reinforced With Frp

Research on NCF fabric CFRP pultrusion beam mechanical performance and laminate design for railway vehicle application

Experimental study on performance of CFRP-strengthened RC beams with geopolymer and epoxy

Experimental and Theoretical Investigation on Shear Behaviour of Small-Scale Timber Beams Strengthened with Fiber-Reinforced Polymer Composites

Flexural Behavior of Frp and Steel Reinforced Glulam Beams: Experimental and Theoretical Evaluation

Fibre-Reinforced Polymers and Steel for the Reinforcement of Wooden Elements-Experimental and Numerical Analysis

Experimental, Analytical, and Numerical Assessments for the Controversial Elastic Stiffness Enhancement of CFRP-Strengthened Timber Beams

Flax, Basalt, E-Glass FRP and Their Hybrid FRP Strengthened Wood Beams: An Experimental Study

Experimental Study of the Flexural and Compression Performance of an Innovative Pultruded Glass-Fiber-Reinforced Polymer-Wood Composite Profile

Mechanical Properties of Full-Scale Wooden Beams Strengthened with Carbon-Fibre-Reinforced Polymer Sheets

Evaluation of the longitudinal restraint, uplift resistance, and long-term performance of high-density polyethylene crosstie rail support system using static and cyclic loading

Strengthening Timber Structural Members with CFRP and GFRP: A State-of-the-Art Review