Abstract:In order to solve the problem of shield hobbing cutter failure due to bias wear and chipping during tunnel boring, TiC-WC/Ni60 coating was prepared on the surface of H13 steel to improve the wear resistance of shield hobbing cutter. In this paper, four kinds of WC-TiC/Ni60 composite coatings with different content ratios of 5 wt% TiC+25 wt% WC, 10 wt% TiC+20 wt% WC, 15 wt% TiC+15 wt% WC and 20 wt% TiC+10 wt% WC were prepared on the surface of H13 steel by using the coaxial powder-feeding laser cladding equipment. The micromorphology, phase, hardness and friction and wear properties were fully studied. The results show that cross-sectional organization of the fused cladding layer mainly consists of columnar crystals, cytocrystals and equiaxial crystals; the hard phases in the fused cladding layer mainly consist of TiWC 2 , Cr 4 Ni 5 W, and Cr 3 C 2 , and so on; The microhardness of the cross-section of the fused cladding layer shows a trend of decreasing at first, then increasing and finally decreasing, and the highest hardness of the fused cladding layer occurs at the subsurface of the fused cladding layer; the friction coefficient of the fused cladding layer shows a trend of decreasing first and then increasing; the wear volume of the fused cladding layer is significantly lower than that of the substrate, and the wear volume of the 15 wt% TiC coating is the smallest of 1.313 mm 3 , which is 86.9 % lower than that of the substrate; the wear mechanism of the substrate is mainly abrasive wear and adhesive wear, and the wear mechanism of the fused cladding layer is mainly brittle spalling, abrasive wear and oxidative wear. The analysis of the experimental results shows that the surface properties of the coating are best when both TiC and WC contents are 15 wt%.

Characterization of Laser Cladding Wc-Ti Composite Coatings

Research of Ni/WC Composite Coatings on TC4 titanium Alloy by Laser Cladding

Microstructure and Properties of WC Reinforced Ni-based Composite Coatings with Y2O3 Addition on Titanium Alloy by Laser Cladding

Study of Microstructure and Properties of Laser Cladding Ni60-WC + TiC Composite Coating

Effect of laser power on microstructure and properties of Ti-Al/WC composite coatings

Microstructure and Wear Resistance of Laser Cladding TiC Coat on Titanium Alloy

Study Of Wear And Corrosion Resistances Of Ni60-Wc + Tic Composite Coating

Microstructure and Wear Resistance of Ti6Al4V Titanium Alloy Laser-Clad Ni60/WC Composite Coating

Laser Cladding of Electroplated Ni-WC on Surface of TA2:microstructure and Mechanical Properties

Microstructure and tribological properties of laser cladded TiC reinforced WC-10Co4Cr coatings at 500 °C

Microstructure and wear resistance of laser clad composite coating on TC4 titanium alloy surface

Microstructure and Properties of Laser Cladding TiC/TiAl Composite Coatings on Γ-Tial Intermetallic Alloy

Development and Characterization of Laser Clad High Temperature Self-Lubricating Wear Resistant Composite Coatings on Ti–6Al–4V Alloy

Microstructural Evolution and Abrasive Resistance of WC7Co Ceramic Particle-Reinforced Ti6Al4V Composite Coating Prepared by Pulse Laser Cladding

Microstructure evolution and tribological behavior of laser cladded Al 1.8 CrCuFeNi 2 /WC composite coatings on Ti-6Al-4 V

Tribological Behaviour of Laser-Clad TiCp Composite Coating

Study on the friction and wear performance of laser cladding WC-TiC/Ni60 coating on the working face of shield bobbing cutter

Effect of linear energy density on microstructure and wear resistance of WC-Co-Cr composite coating by laser cladding

The Influence of the Pre-Placed Powder Layers on the Morphology, Microscopic Characteristics and Microhardness of Ti-6Al-4V/WC MMC Coatings During Laser Cladding

Microstructure and properties of Ti–Al–C composite coatings prepared by laser cladding

Microstructure and Properties of TiAl Composite Coatings Prepared by Laser Cladding under Multi-Phase β0/CoAl2Ti Phase Strengthening