Mechanism of Periodically Distributed Fracture in Reinforced Concrete Beam under Uniaxial Tension

Zhang Juanxia,Tang Chun'an,Kou Shaoquan,Liang Zhengzhao,Xu Tao

DOI: https://doi.org/10.3969/j.issn.1000-4939.2007.04.031

2007-01-01

Abstract:A numerical code RFPA3D(Three-Dimension Realistic Failure Process Analysis) is employeel to simulate the three-dimensional failure process of reinforced concrete under uniaxial tension. Then the an ...

What problem does this paper attempt to address?

Automated Finite Element Modeling and Analysis of Cracked Reinforced Concrete Beams from Three Dimensional Point Cloud

Ke Yu,Congguang Zhang,Mohammed Shooshtarian,Weijian Zhao,Jiangpeng Shu

DOI: https://doi.org/10.1002/suco.202100194

2021-01-01

Structural Concrete

Abstract:Modeling and assessing the load‐carrying capacity of reinforced concrete (RC) structures that are cracked is important because the condition of an RC structure changes due to natural aging and accumulated damage. The current approach to determining the residual capacity of a cracked RC structure is time‐consuming and error‐prone due to a limited capacity to obtain and process structural information. In this study, an automated approach was proposed to determining residual capacity by performing finite element (FE) analysis of an RC structure using point cloud three dimensional modeling. Two simply supported RC beams were subjected to bending tests to provide validation data. The initial activity was to extract dimensional data from laser‐scanned point cloud data of a beam. The information obtained was used to automatically generate nonlinear FE models of the beam that was used for nonlinear FE analyses in Abaqus. An initial crack was added to the beam to model a cracked beam in real conditions. Three different models were used to simulate initial cracks, a weakened element model, a cohesive zone model, and an extended FE model. The results indicate that the proposed method of automating the combination of point cloud data with nonlinear FE analysis provides a novel practical approach to modeling and assessing cracked RC beams.
EXTEND FINITE ELEMENT NUMERICAL SIMULATION FOR CRACK PROPAGATION OF FIBER CONCRETE

Lei ZHANG,Jin-chang WANG

DOI: https://doi.org/10.3969/j.issn.1001-6864.2012.04.014

2012-01-01

Abstract:Through introducing the concepts of extend finite element method(XFEM),applying the finite element method of ABAQUS to analyze the crack propagation of three-point bending concrete beams(Mode I) and the cracking behavior of different fiber reinforced concrete.Finally,the results are compared and evaluated.By the extend finite element numerical simulation for the crack propagation and fracture of concrete,this paper represents the special advantage in term of failure of fracture.
Developing a Three-Dimensional Finite Element Analysis Approach to Simulate Corrosion-Induced Concrete Cracking in Reinforced Concrete Beams

Y. Z. Wang,Y. X. Zhao,F. Y. Gong,J. F. Dong,Koichi Maekawa

DOI: https://doi.org/10.1016/j.engstruct.2022.114072

IF: 5.582

2022-01-01

Engineering Structures

Abstract:Corrosion-induced concrete cracking is a significant stage of structural deterioration in reinforced concrete (RC). Numerous numerical studies were conducted to address this problem, but relatively few considered the effects of stirrups and non-uniform corrosion in three dimensions. In this study, a three-dimensional finite element analysis (FEA) approach was developed to simulate corroded RC beams, considering non-uniform steel corrosion and a detailed arrangement of stirrups. The cracking patterns obtained from the simulation results agreed well with experimental observations. Subsequently, using the proposed FEA approach, the effects of the non-uniform corrosion and stirrup constraints on the cracking pattern were investigated. The simulation results indicated that an RC structure under non-uniform corrosion showed more severe cracking and reached the serviceability limit state earlier. The stirrups limited the propagation of the corrosion-induced cracks, but the constraint weakened with increasing distance from the location of the stirrups.
Numerical Simulation of Fracture and Damage Behaviour of Concrete at Different Ages

Nanguo Jin,Ye Tian,Xianyu Jin

DOI: https://doi.org/10.12989/cac.2007.4.3.221

2007-01-01

Abstract:Based on the experiment results, the damage and fracture behavior of concrete at the ages of ld, 2d, 7d and 28d, in three-point bending and uniaxial tensile tests, were simulated with a finite element S program, ABAQUS. The critical stress intensity factor K-IC(3) and the critical crack tip opening displacement (CTODC) of concrete were calculated with effective-elastic crack approach for the three-point bending test of grade C30 concrete. Based on the crack band model, a bilinear strain-softening curve was derived to simulate the LOAD-CMOD curves and LOAD-Displacement curves. In numerical analysis of the uniaxial tension test of concrete of grade C40, the damage and fracture mechanics were combined. The smeared cracking model coupling with damaged variable was adopted to. evaluate the onset and development of microcracking of uniaxial tensile specimen. The uniaxial tension test was simulated by invoking the damage plastic model which took both damage and plasticity as inner variables with user subroutines. All the numerical simulated results show good agreement with the experimental results.
Numerical simulation of cracking of early-age concrete three-point beams

Meng QU,Nan-guo JIN,Xian-yu JIN,Ye TIAN

DOI: https://doi.org/10.3785/j.issn.1008-973X.2006.07.026

2006-01-01

Abstract:A finite element program, ABAQUS was used to simulate fracture experiment under three-point bending C30 concrete at ages of 1, 2, 7, and 28 d. Based on the crack band model, a bilinear strain-softening curve was derived with the parameters determined by curve fitting for the three-point bending tests. Comparison between the simulated P-δ m curve and experimental results showed good agreement. Meanwhile, comparisons between numerical P-δ m curves and P-A curves for concrete at different ages also showed good agreement. By applying the linear elastic fracture mechanics (LEFM) method, the critical stress intensity factor and critical crack tip opening displacement (δ t) of concrete were calculated and compared with the test results. It was found that the simulation and experimental results were close to each other.
3D Finite Element Simulation of Complex Static and Dynamic Fracture in Quasi-Brittle Materials

xiangting su,zhenjun yang,guohua liu

DOI: https://doi.org/10.1007/978-90-481-2822-8_120

2009-01-01

Abstract:This study proposes a simple but effective finite element method to simulate complex 3D crack propagation in quasi-brittle materials such as concrete. Cohesive interface elements, characterized by softening traction-separation constitutive laws, are embedded into initial meshes to model potential cracks. The method is implemented in connection with Abaqus. Various concrete structures under static and dynamic loadings were modeled with excellent results compared with experiments.
NUMERICAL SIMULATION OF FAILURE BEHAVIOR OF REINFORCED CONCRETE FRAME STRUCTURES BY DISCRETE ELEMENT METHOD

Wei-liang JIN,Tao FANG

DOI: https://doi.org/10.3969/j.issn.1000-4750.2005.04.014

2005-01-01

Abstract:Discrete element method has been an effective approach for simulating damage process of structures. A rectangular discrete element model is extended by applying nodal element and considering the non-linearity of concrete material in this paper. The failure criterion, formula and determination of analytical parameters such as spring modulus of the extended model are presented. The computational efficiency of the extended model is improved by applying double listing technique in the program. The collapse process of reinforced concrete frame due to explosion is simulated. Results show that the extended discrete element method achieves good simulation of collapse process of reinforced concrete frame structures.
Dynamic Fracture Catastrophe Model of Concrete Beam under Static Load

Zhonggou Chen,Chuanqing Fu,Yifeng Ling,Xianyu Jin

DOI: https://doi.org/10.12989/cac.2020.25.6.517

2020-01-01

Abstract:An experimental system on three point bending notched beams was established to study the fracture process of concrete. In this system, the acoustic emission (AE) was used to build the cumulative generation order (AGO) and dynamically track the process of microcrack evolution in concrete. A grey-cusp catastrophe model was built based on AE parameters. The results show that the concrete beams have significant catastrophe characteristic. The developed grey-cusp catastrophe model, based on AGO, can well describe the catastrophe characteristic of concrete fracture process. This study also provides a theoretical and technical support for the application of AE in concrete fracture prediction.
Numerical Analysis and Punching Shear Fracture Based Design of Longitudinal Plate to Concrete-Filled CHS Connections

Fei Xu,Ju Chen,Tak-Ming Chan

DOI: https://doi.org/10.1016/j.conbuildmat.2017.08.098

IF: 7.4

2017-01-01

Construction and Building Materials

Abstract:The mechanical behaviour of longitudinal plate-to-concrete-filled circular hollow section (CHS) connections under axial tension, eccentric tension and in-plane bending is extensively studied by the experimentally validated finite element analysis (FEA) in this paper. A total of 336 connections with a wide range of parameters on geometrical configurations, material properties and load positions was conducted to investigate (a) the general applicability of the experimental conclusion for the governing limit state, (b) the shear stress profile on the failure face and (c) the design equations based on fracture analytical models under various loading conditions. FEA extended the validity of experimental conclusion that the only governing limit state was punching shear failure instead of the deformation limit of 3% chord diameter (D). With an aim of proposing design equations based on ductile fracture mechanics, the stress distributions on the fracture failure face and the inner concrete were investigated by the parametric study, and then were adopted in the analytical models. Finally, design equations based on semi-theoretical models for the ultimate strength of longitudinal plate-to-concrete-filled CHS connections under three investigated loads were proposed. It is found the connection-capacity predictions agreed with both test and FEA results well.
Simulation of Meso-Fracture for Concrete Based on the Developed Random Aggregate Model

TANG Xinwei,ZHANG Chuhan

DOI: https://doi.org/10.3321/j.issn:1000-0054.2008.03.012

2008-01-01

Abstract:Based on former meso-mechanics models,an efficient aggregates deposition method and an elements division criterion are developed in order to study the mechanical characteristic and the failure mechanism of concrete better.Based on the continuum mechanics,a reasonable meso-mechanics model of concrete and a parameters chosen method for meso-elements are presented which use the elastic damaged stress-strain relations to describe mechanical behaviors of the concrete.Numerical experiments with random distribution of aggregates for concrete samples for simulating Petersson's 3-point bending beam are then accomplished,from which the failure mechanism of concrete on meso scale is investigated.It is shown that the numerical mode is able to capture the complete process of concrete mode-I tensile fracture,which shows good agreement with corresponding experimental results.
NUMERICAL SIMULATION OF FAILURE PROCESS OF THREE-POINT BENDING CONCRETE BEAM CONSIDERING HETEROGENEITY OF TENSILE STRENGTH AND POST-PEAK SOFTENING CURVE

WANG Xue-bin,ZHANG Jun

2009-01-01

Abstract:Considering the heterogeneity of the tensile strength and post-peak softening curve, failure processes of two three-point bending concrete beams are numerically modeled using FLAC. The load-CMOD curve, the distributions of the horizontal stress and plastic tensile strain in the middle span of the beam, the length of the strain localization zone and real crack, and the distributions of failed elements in tension and real crack are presented. Quantitatively, the numerical load-CMOD curves are consistent with the experimental results of C40 concrete. After the heterogeneity of the tensile strength and post-peak softening curve are considered, real cracks are initiated at several spots. Then real cracks initiated coalesce and simultaneously new real cracks are initiated. After the peak load, the increasing tendency of the length of the strain-softening region becomes slower at higher CMODs. After real cracks are initiated, the length of the strain-softening region approximately remains constant. As CMOD increases, initially, the beam does not rotate around the cross section in the middle span and then the rotational angle approximately remains constant that is followed by the rotational angle becoming larger and larger. The thickness of the tensile strain localization region is about 3 to 4 times of the element size.
Numerical Experiment on Size Effect for Sfrc Splitting Fracture

Fu Chuan Qing,Jin Xian Yu,Tian Ye,Jin Nan Guo

DOI: https://doi.org/10.4028/www.scientific.net/amr.250-253.335

2011-01-01

Abstract:Based on the MFPA(2D) software system and test method of the wedge splitting fracture in the Lab., a numerical model was established. The numerical experiments on wedge splitting fracture with plain concrete and SFRC (steel fiber reinforced concrete) were carried on. The calculation results about plain concrete with different dimensions and ligament length proved the numerical model is effectively on numerical calculation, and have a good agreement with the results of the test results. Then, the process of crack initiation, propagation of SFRC specimens with different dimensions and fitting formula about size effect were given. The results indicated that the size effect existed in the splitting fracture energy of SFRC.
A Numerical Analysis with Scaled Boundary Finite Element Method to Simulate Mixed-mode Crack Propagation for Concrete Beams

YU Xue-fang,LIU Guo-hua

DOI: https://doi.org/10.3321/j.issn:0529-6579.2008.02.006

2008-01-01

Abstract:Based on linear elastic fracture mechanics and the scaled boundary finite element method(SBFEM),numerical simulation was performed for a mixed-mode crack propagation model.From comparing the results with which obtained by the nonlinear finite element method(NFM),SBFEM can predict crack trajectories and compute lod-displacement relations as well as load-deflection at loading point accurately and efficiently.
Fracturing behaviors of FRP-strengthened concrete structures

Zhishen Wu,Jun Yin

DOI: https://doi.org/10.1016/S0013-7944(02)00100-5

IF: 5.4

2003-01-01

Engineering Fracture Mechanics

Abstract:In this paper, we focus on the study of concrete cracking behavior and interfacial debonding fracture in fiber reinforced polymer (FRP)-strengthened concrete beams. An experimental program is systematically reviewed according to the observed failure modes, in which it is found that the interfacial debonding may propagate either within the adhesive layer or through concrete layer in the vicinity of bond interface. A finite element analysis is performed to investigate the different types of debonding propagation along FRP–concrete interface and crack distribution in concrete. For the numerical fracture models, interfacial debonding that initiates and propagates in adhesive layer is modeled by fictitious interfacial crack model. And concrete cracking, including the debonding fracture through interfacial concrete, is modeled by smeared crack model. Properties of the interfacial adhesive layer and concrete are considered to significantly influence the debonding propagation types and crack distribution. The interactions between interfacial bond strength, interfacial fracture energy of bond adhesive layer and tensile strength, fracture energy of concrete are discussed in detail through a parametric study. According to the results, the effects of these properties on different types of interfacial debonding, concrete cracking behavior and structural load-carrying capacity are clearly understood.
3D meso-scale fracture modelling and validation of concrete based on in-situ X-ray Computed Tomography images using damage plasticity model

Yujie Huang,Zhenjun Yang,Wenyuan Ren,Guohua Liu,Chuanzeng Zhang

DOI: https://doi.org/10.1016/j.ijsolstr.2015.05.002

IF: 3.667

2015-01-01

International Journal of Solids and Structures

Abstract:Three-dimensional (3D) meso-scale finite element models of concrete based on in-situ X-ray Computed Tomography (XCT) images are developed and validated in this study. The micro-scale images from a Brazilian-like XCT test are first compressed and then transformed into manageable meso-scale 3D meshes using a voxel hexahedron meshing technique with a stacking algorithm. The continuum damage plasticity model is used to simulate complicated damage and fracture behaviour. Excellent qualitative agreement is found between modelling and the XCT compression test in terms of damage evolution and fracture process on both the surface and interior of the specimen. 3D uniaxial tension tests are also simulated, and it is found that the distribution of voids have profound influences on the strength and crack patterns. The image-based 3D models are proved very promising in elucidating fundamental mechanisms of complicated crack initiation and propagation behaviour that 2D studies are incapable of modelling.
3-D Fixed Multi-Directional Crack Model for Reinforced Concrete Structure

HAN Tao,AN Xuehui

DOI: https://doi.org/10.3321/j.issn:1000-0054.2008.06.010

2008-01-01

Abstract:The mechanics of multi-directional cracks was analyzed to study the interactions between different direction cracks occurring at same location in reinforced concrete structures subjected to complex loadings. A 3-D fixed multi-directional crack model was developed and verified through constitutive model tests and simulations. Reinforced concrete beam experiments using regular hexagonal cross section beams were used to study the mechanics of the multi-directional cracking. The 3-D cracks crossed each other as the loadings were applied on different surfaces and at different locations on the reinforced concrete beams. Numerical simulations of these tests were studied using the model. Simulations show that the entire tests including the crack growth and bearing capacity can be accurately analyzed by the model.
Finite Element Modelling of Concrete Cover Separation Failure in FRP Plated RC Beams

ZJ Yang,JF Chen,D Proverbs

DOI: https://doi.org/10.1016/s0950-0618(02)00090-9

IF: 7.4

2002-01-01

Construction and Building Materials

Abstract:The technique of bonding fibre reinforced polymer (FRP) composites to the tension face or sides of reinforced concrete (RC) beams has become very popular for strengthening or retrofitting purposes. A distinct characteristic of such strengthened RC beams is that they very often fail due to various premature debonding failures. This paper presents a fracture mechanics based finite element analysis of debonding failures. Numerical results for an experimental beam are presented. Initial findings show that the method can successfully simulate the concrete cover separation failure mode in FRP strengthened RC beams.
Numerical Simulation of Crack Growth of Reinforced Concrete Beam Based on XFEM

杨涛,邹道勤

DOI: https://doi.org/10.3785/j.issn.1008-973x.2013.03.014

2013-01-01

Abstract:The cracking process of a simply supported reinforced concrete beam was simulated by the extended finite element method(XFEM).The concrete and rebars were simulated by the 3-D solid elements and 3-D truss elements respectively.Initial cracks which kept a same space with the experimental result were predefined.The bond-slip effect between concrete and rebars was considered by the nonlinear springs elements.Based on this,the crack growth state during the loading process,the influence to the crack extension by the bond-slip,the relationship between crack width and external force,as well as the stress distribution of the concrete and rebars in pure bending region were obtained by simulation.The analysis showed that the calculated crack width was in good agreement with the experimental value,bond-slip would make the cracks wider at the same load level,and the calculated stress distributions of the concrete and rebars were consistent with the actual situation.XFEM is an efficient method to simulate the crack of reinforced concrete beam without remeshing and predefining the crack propagation path.
Ⅰ/Ⅱ TENSILE-SHEAR MIXED MODE FRACTURE SIMULATION BY 3D DISCRETE ELEMENT METHOD

HOU Yan-li,ZHOU Yuan-de,ZHANG Chu-han

DOI: https://doi.org/10.3969/j.issn.1000-4750.2007.03.001

2007-01-01

Abstract:For numerical simulation of transition process from continua to discontinua, theⅠ/Ⅱ tensile-shear mixed mode fracture of quasi-brittle materials such as concrete and rock is analyzed by coupling respectively the smeared rotating crack model and the discrete crack model with deformable discrete element method(DEM). The zoning of tensile-shear failure criterion and the gradual reduction of stiffness and strength driven by the normal opening of crack are proposed based on the joint-contact constitutive relationship of deformable discrete element method. The models are applied to analyze the nonsymmetric three-point bending beam with a single-edge notch. The comparison between experimental and numerical results shows that the two nonlinear fracture models are both capable of predicting the initiation and propagation of the crack. It also shows that the crack initiateds withⅠ/Ⅱ tensile-shear mixed mode but steadily propagated predominantly in mode Ⅰ under mixed loading. It is also concluded that the discrete crack model based on DEM is capable of simulating the entire fracture to collapse process of the loaded system.
EXPERIMENTAL RESEARCH AND NUMERICAL SIMULATION OF 3D MULTI-DIRECTIONAL CRACKING IN RC BEAM

HAN Tao,AN Xue-hui

2009-01-01

Abstract:Existing cracks in RC structure influence the formation and propagation of new cracks, thus affect the behavior of the whole structure. Experiments on RC beams with regular hexagon cross section were carried out to study the mechanism of multi-directional cracking and its influence on the bearing capacity. Five-stage loading was applied. Bending cracks were designed to occur during the first 2 stages, penetrating the swhole cross section, then, changing loading condition, diagonal shear cracks were designed to cross the existing bending cracks during the next three stages. Multi-directional Crack propagations were observed, and reaction-displacement curves were recorded in experiments. The mechanism of 3D multi-directional cracking and its influence on bearing capacity were discussed, and a 3D fixed multi-crack model was developed. Adopting the newly developed model, a finite element analysis was performed. A comparison between numerical and experimental results shows that this model can be applied to analyze multi-directional cracking.

Mechanism of Periodically Distributed Fracture in Reinforced Concrete Beam under Uniaxial Tension

Automated Finite Element Modeling and Analysis of Cracked Reinforced Concrete Beams from Three Dimensional Point Cloud

EXTEND FINITE ELEMENT NUMERICAL SIMULATION FOR CRACK PROPAGATION OF FIBER CONCRETE

Developing a Three-Dimensional Finite Element Analysis Approach to Simulate Corrosion-Induced Concrete Cracking in Reinforced Concrete Beams

Numerical Simulation of Fracture and Damage Behaviour of Concrete at Different Ages

Numerical simulation of cracking of early-age concrete three-point beams

3D Finite Element Simulation of Complex Static and Dynamic Fracture in Quasi-Brittle Materials

NUMERICAL SIMULATION OF FAILURE BEHAVIOR OF REINFORCED CONCRETE FRAME STRUCTURES BY DISCRETE ELEMENT METHOD

Dynamic Fracture Catastrophe Model of Concrete Beam under Static Load

Numerical Analysis and Punching Shear Fracture Based Design of Longitudinal Plate to Concrete-Filled CHS Connections

Simulation of Meso-Fracture for Concrete Based on the Developed Random Aggregate Model

NUMERICAL SIMULATION OF FAILURE PROCESS OF THREE-POINT BENDING CONCRETE BEAM CONSIDERING HETEROGENEITY OF TENSILE STRENGTH AND POST-PEAK SOFTENING CURVE

Numerical Experiment on Size Effect for Sfrc Splitting Fracture

A Numerical Analysis with Scaled Boundary Finite Element Method to Simulate Mixed-mode Crack Propagation for Concrete Beams

Fracturing behaviors of FRP-strengthened concrete structures

3D meso-scale fracture modelling and validation of concrete based on in-situ X-ray Computed Tomography images using damage plasticity model

3-D Fixed Multi-Directional Crack Model for Reinforced Concrete Structure

Finite Element Modelling of Concrete Cover Separation Failure in FRP Plated RC Beams

Numerical Simulation of Crack Growth of Reinforced Concrete Beam Based on XFEM

Ⅰ/Ⅱ TENSILE-SHEAR MIXED MODE FRACTURE SIMULATION BY 3D DISCRETE ELEMENT METHOD

EXPERIMENTAL RESEARCH AND NUMERICAL SIMULATION OF 3D MULTI-DIRECTIONAL CRACKING IN RC BEAM