Design of Public Address System Based on Ethernet and Digital Techniques

祁才君

DOI: https://doi.org/10.3969/j.issn.1002-8684.2010.05.018

2010-01-01

Abstract:The characteristic of the PA(Public Address) based on Ethernet and digital, visa traditional analogue PA, is analyzed. Those product designed by CobraNet techniques are discussed in detail. An Ethernet digital PA is established using CobraNet device.

What problem does this paper attempt to address?

Design of IPPBX based on embedded system

Yuemei YANG,Pingshan CHEN,Dongqin FENG

DOI: https://doi.org/10.16652/j.issn.1004-373x.2015.12.022

2015-01-01

Abstract:With the packet exchange principle,IPPBX can realize the functions of the traditional PBX on Ethernet and overcome the insufficiency of traditional PBX effectively. It has powerful functions,comprehensive services with less cost. The typical networking mode of IPPBX is introduced in this paper. The design principles of each module system MPC8250 hardware system based on IPPBX and the software system of the system are given. The protocol conversion software of main con?trol module is also analyzed. The test result shows that the system can achieve simultaneous processing of 200 calls and its voice quality is excellent.
REAL-TIME MONITORING SYSTEM FOR THE STATES OF POWER NETWORK OVER ETHERNET AND ATM

严登俊,袁洪,高维忠,吴峰,鞠平

DOI: https://doi.org/10.3321/j.issn:1000-1026.2003.10.016

2003-01-01

Abstract:In present, the communication delay is uncertain and the number of the phase measurement unit (PMU) is limited in the supervisory and control system for dynamic stability. In order to make full use of the accuracy and high speed of computer network in data transmission, a transfer system for PMU data is built based on a combination of Ethernet and ATM. In the system, the communication delay, which is produced by the CSMA/CD in Ethernet, is reduced by using the Ethernet switch combined with the ATM switch. The error rate is also reduced because the program of the communication is programmed with the Windows Socket and TCP/IP protocol. Based on the fibre-optic telecommunication cable, a real-time transmission channel for the whole network phasor information is constructed. In the engineering practice, the system can transmit data one time in one circle to realize the real-time monitoring of the power network operation situation based on the PMU wide area measured data.
System Design of Network Digital Audio Processor

LI Xin-qiu,QI Cai-jun

DOI: https://doi.org/10.3969/j.issn.1002-8684.2006.01.016

2006-01-01

Abstract:In this paper, a network digital audio processor based on CobraNet and DSP is developed. The function of realtime performance of audio transmission of CM2(the hardware of CobraNet)and 21161N's on chip processing and communication are combined in this processor. Digital signal processing flows and algorithms are configured with PC. The solution of the processor is described in detail.
An Image Acquisition System of Stereo Vision Base on Ethernet Technology

ZHAO Jian,LIU Ji-lin,YU Hai-bin

DOI: https://doi.org/10.3969/j.issn.1002-8692.2005.12.025

2005-01-01

Abstract:A stereo image collecting platform based on DSP and the Ethernet technology has been designed. The pairs of images obtained from two CMOS image sensors are transmitted to the PC through the Ethernet after processing by DSP. The double RAM structure of ping-pong buffer is used for expanding the throughput of data. This paper discusses the detailed expatiation about the principle of design and the connection of system interfaces. Finally, test result of the throughout of packets transmitted on the Ethernet is given.
Lectures on “Industrial Ethernet and Its Application Technology” Chapter Ⅵ The Structure of Distributed Networking Control System Based on EPA

冯冬芹,金建祥,王为民,褚健

DOI: https://doi.org/10.3969/j.issn.1000-0380.2003.09.024

2003-01-01

Abstract:0 引言当前,在多种现场总线标准并存,无法形成统一的标准的形势下,以以太网和无线技术为代表的商用COTS(Commercial-Off-The-Shelf)技术在工业企业综合自动化系统中的信息管理层、监控层网络得到了广泛应用,并有直接向下延伸,应用于工业测量与控制系统的现场设备层网络的趋势.以太网+TCP(UDP)/IP逐渐称为事实上的工业标准.
Design of CobraNet audio network router

QI Cai Jun,ZHAO Fan,WANG Pei Liang

DOI: https://doi.org/10.3969/j.issn.0258-7998.2008.02.033

2008-01-01

Abstract:The paper looks back the development process of CobraNet technology and analyzes the CS1810xx CobraNet net- worked audio system processors.The hardware structure of CobraNet router designed using CSl810xx is given.The Ethernet inter- face circuit of CSl810xx,the firmware load method for CSl810xx,the host management interface between CS1810xx and MCU,etc. is discussed in detail.
EPA-based Open Network Control System

Dongqin Feng,Wenjun Huang,Jianxiang Jin,Jian Chu

DOI: https://doi.org/10.1109/icca.2003.1595168

2003-01-01

Abstract:The Ethernet is more and more used in the industrial environments. Because of the non-deterministic protocol of CSMA/CD, Ethernet is thought not to be suitable for the control of real time applications. With the worldwide application and development of Ethernet, its transmission rate is considered sufficiently high enough to estimate that all messages can be received inside a predefined temporal window. Especially, using Ethernet in industrial network will brings a lot of advantages: (1) consistency with the other communication systems installed in the enterprise; (2) employment of the same hardware all over the factory; (3) short cycle-times due to the high transmission speed; (4) large availability of chips implementing the MAC protocol, etc. In this paper, we first analyze the real-time capability of Ethernet and features of traffic for industrial network. Then, we propose some technologies for the design of an Ethernet-based real-time application. Finally, we present an EPA (Ethernet for Plant Automation)-based open network control system.
Design Issues Of Building Block Structure Communications For Power Electronic System

Yao Zhang,Hao Ma,Fei Xu

DOI: https://doi.org/10.1109/PESC.2006.1712222

2006-01-01

Abstract:Some novel communication strategies for power electronic system are presented in this paper, and design issues can be described from bottom to top layer, like building block. The basic communication unit as the bottom layer plays the leading role in the overall design. Based on the variance of the control mode and the demand in communication, power electronic device (PED) or power electronic system (PES) can be divided into one or several salve nodes in bottom communication layer. The complex communication architecture, the higher level, is described in detail from the point of view of field bus, connection for Internet and completely distributed network. Architecture for each communication design, key feature of the network, and diverse application example are discussed. Two novel plans about completely distributed network for PED/PES and the method of information grouping are proposed.
Design of DSP Embedded System Based on Ethernet Hardware Protocol Stack

邹依依,郭灿新,欧阳三元,黄成军,江秀臣

DOI: https://doi.org/10.3969/j.issn.1000-0380.2008.11.018

2008-01-01

Abstract:The DSP embedded system offering high speed transmission function for network data is designed and implemented by adopting the technology of Ethernet hardware protocol stack chip.The dedicated chip W5100 is selected for Ethernet,that chip is suitable for using in embedded system and possess Internet protocol.Through configuring system network information,the TCP and UDP connection in whole system can be realized for data transmission in Server or Client mode.With DSP embedded data acquisition system based on W5100 as example,through reasonable programming and configuring each register,the verification shows that successful data transmission through Ethernet can be conducted for the system.
A Novel Method To Build Smart Networked Alarm System Based On Cid

Jx Zou,Hb Xu,Xj Zhou

2005-01-01

Abstract:In most existing smart networked alarm systems, the control and status signals are transmitted in PSTN (Public Switched Telephone Network) using DTMF (Dual Tone Multi Frequency) technology. It needs establish connection before data transmission. But it is proved that the running cost of the existing systems is high because of the frequent signals transmission, and the response time is too long. A novel method is proposed in this paper to design a smart networked alarm system based on CID (Calling Identity Delivery) technology. The system formed by this method has advantages of shorter response time and lower running cost. The networked system, which consists of user terminals and control center, can transmit data to the control center rapidly through phone lines after alarms are touched off in the case of on-hook and off hook. The realization of the system control functions and communication protocols under single terminal mode and mufti-terminals mode are both described in detail. The system runs reliably in practice and performs very well.
Design of IP Telephone Based on TMS320C5402

侯建军,柳立鹏,邵文龙

DOI: https://doi.org/10.3969/j.issn.1673-0291.2001.03.028

2001-01-01

Abstract:A DSP-based solution to LAN/Intranet-oriented IP telephone is presented. This IP Telephone can be used either as a desktop PC peripheral or as an Intranet network terminal. Its cores are TMS320C5402 in charge of voice code and MPC860T in charge of communications protocol processing and control logic. Several kinds of interface including USB, RS232 and RJ45 are designed to allow IP telephone to connect with other equipment in flexible ways. Some details of hardware architecture are discussed in this paper.
Design of Embedded CAN-ethemet Gateway Based on DSP

赵晓军,曹勇,苏海霞,任明伟

DOI: https://doi.org/10.16208/j.issn1000-7024.2009.03.075

2009-01-01

Abstract:In order to accomplish the data exchange between field device and Ethernet, make an in-depth exchange of information to the industrial scene, achieve the underlying equipment and the Internet to connect seamlessly, a CAN-Ethernet connection scheme based on DSP is put forward. The DSP and Ethernet interface methods and CAN/Ethernet protocol conversion methods are presented, to realize he sensor network configuration and dynamic reconfiguration features, it uses self-identification, self-described technology and interoperability of embedded network interface devices under network environment. Experimental results show that embedded CAN/Ethernet network has a good validity and reliability to meet the demand for industrial control networks.
Design of TMS320F2812 Ethernet Interface Based on ENC28J60

Gao Jixing,Zhao Qiang,Tong Weiming

DOI: https://doi.org/10.3969/j.issn.1671-4598.2013.03.050

2013-01-01

Abstract:As an effective DSP,TMS320F2812 can not satisfy the growing requirement of date communication of electric power quality monitoring.The Ethernet interface of TMS320F2812 based on ENC28J60 is designed for the date communication of electric power quality monitoring.Following a brief introduction of EN28J60 and TMS320F2812,the design of Ethernet interface is expatiated,including the design of the peripheral circuit of ENC28J60,the design of drive program and the design of protocol,using the SPI port of TMS320F2812 connect with ENC28J60,using microinstruction programming to realize the control logic of ENC28J60.The net layer and transport layer use embedded TCP/IP protocol,application layer use HTTP protocol.Texting communication by running TCP/UDP Socket on the text computer contact with interface.The stable of communication is verified by test,and the Ethernet communication of TMS320F2812 is realized.
Deterministic and Real-Time Communication over Ethernet in EPA Control System

Chu Jian

DOI: https://doi.org/10.1109/WCICA.2006.1713395

2006-01-01

Abstract:Due to the low price and robustness resulting from its wide acceptance and deployment, ISO/IEC 8802-3 based Ethernet is becoming the de-facto network in DCS and PLC, and is being attempted to connect field devices. It is difficult to build a real-time field control network based on Ethernet because it has unpredictable delay characteristics due to packet collisions. To resolve this problem, some papers and reports presented the so-called hardware methods to improve real-time performance but they changed the circuits of Ethernet. Some other authors designed the so-called software methods (e.g. static or dynamic traffic smoothers by giving Ethernet packets priority) which only reduced the packet collision without avoiding collision. In addition, these methods are designed based on some presuppositions or preconditions and are difficult to be implemented and used in real control systems. Considering that some real-time packets can be divided in two types: (1) cyclic packets (e.g. measurement and control data) which shall be transferred at each communication cycle, and (2) acyclic packets (e.g. configuring data and alert/alarm data) which are transferred randomly, we define a EPA-based Communication Scheduling Management Entity (EPA_CSME) beyond Ethernet MAC protocol referring to ISO/OSI model to avoid collisions in Ethernet system. With the precise time synchronization based on IEC61588 protocol with the same time server, each node has the same absolute time in the whole system.
Design and Realization of EtherNet Communication Node Based on C8051F02x Microcontroller

ZHAO Jing,TONG Weiming,PEI Fei

DOI: https://doi.org/10.3969/j.issn.1001-5531.2007.07.008

2007-01-01

Abstract:The function description and hardware principle of EtherNet communication node based on microcontroller were given. The reduce TCP/IP protocol suite was embeded in industry field devices and data communication based on EtherNet was completed. The protocol layer model was built and the software technology item was analysed. The realization course of every layer protocol was expounded. Then several technical details which are easily ignored and misunderstood in development and realization were put forward and discussed. The design has been successfully applied in temperature monitoring system of factory.
Implementation of Ethernet Communication of Power Quality Parameters

GAO Ji-xing,TONG Wei-ming

DOI: https://doi.org/10.3969/j.issn.1000-3932.2013.02.019

2013-01-01

Abstract:Considering data communication requirement in power quality monitoring,the design scheme of Eth-ernet communication for power quality parameter realized by building ENC28J60-based Ethernet communication interface was proposed.Basing on EN28J60 chip and analysis of communication requirement,the design scheme concerning Ethernet interface,peripheral circuit,transmission,drive program and Ethernet protocol was expounded.
Ethernet Interface Design Based on TMS320VC5402 Digital Signal Process System

QU Yan-bin,FENG Li-guo,SU Jian-yong

DOI: https://doi.org/10.3969/j.issn.1002-2279.2005.04.017

2005-01-01

Microprocessors

Abstract:The features of the RTL8019AS of Ethernet controller are introduced.The Ethernet interface circuit with RTL8019AS in TMS320VC5402 digital signal processor system is degined,and the program is given.The RTL8019AS is in jumper mode.The linkage between DSP and Ethernet local area net can be realized with this interface circuit.
Design of Embedded Ethernet Data Transmission System Based on DSP

Zhou Xin,Fang Yonghua,Liu jiaxiang,Xiong wei

DOI: https://doi.org/10.16526/j.cnki.11-4762/tp.2010.10.029

2010-01-01

Abstract:In order to test and simulation for the spectral signal processing system in project,design embedded ethernet data transmission system based on DSP,using TI's C2000 series TMS320LF2407A and RELTEK's Ethernet controller chip RTL8019AS.This paper introduces the overall design of the system,given the architecture of this data transmission system,and further analysis the design process of the system hardware and software,.After the system software and hardware passed,use the tweisted-pair cable connect data transmission to PC,at the same time connect data transmission system to spectral signal processing system by plug-ins,then debug the system,the debugging results showed that it can transmit spectral data real-time and reliably,well applied to the practice.
Application of W5100 in DSP Remote Ethernet Communication System

邹依依,郭灿新,黄成军,王瑶,江秀臣

DOI: https://doi.org/10.3969/j.issn.1001-182X.2008.08.009

2008-01-01

Abstract:W5100 is an embedded hardware protocol chip on Ethernet.It contains TCP/IP protocol,Ethernet Mac and PHY,and supports many kinds of net protocols at the same time.The inside configuration and registers of W5100 chip are introduced here.Without any complicated programming and debugging on Ethernet protocols,it is easily to be connected in the internet through simple process.In this example that realized DSP remote Ethernet communication based on W5100 and TMS320C6713,particular operation manners,interface,timing and program realization were introduced in the article.
Design of Building Intercom System Based on Power Line Carrier

Li You

2010-01-01

Abstract:To the question that traditional building intercom system is complex in wiring and high cost in construction of the status quo,a building intercom system based on power line carrier without rewiring was designed.Any two commu-nication terminals in this system can communication by dialing up in the same electricity grid in existence.Speech sig-nal after a process of acquisition and compression by GSM6.10 algorithm can be transferred by the power line and be played after it receiving and decompression by another terminal.After this compression and decompression,it can im-prove network bandwidth utilization as well as reduce transmission bit rate.The results prove that the system can not only meet the requirement of the access control function and it is easy to extended and maintained as well.It is cost-less but useful,so it has a great space for development in smart building.

Design of Public Address System Based on Ethernet and Digital Techniques

Design of IPPBX based on embedded system

REAL-TIME MONITORING SYSTEM FOR THE STATES OF POWER NETWORK OVER ETHERNET AND ATM

System Design of Network Digital Audio Processor

An Image Acquisition System of Stereo Vision Base on Ethernet Technology

Lectures on “Industrial Ethernet and Its Application Technology” Chapter Ⅵ The Structure of Distributed Networking Control System Based on EPA

Design of CobraNet audio network router

EPA-based Open Network Control System

Design Issues Of Building Block Structure Communications For Power Electronic System

Design of DSP Embedded System Based on Ethernet Hardware Protocol Stack

A Novel Method To Build Smart Networked Alarm System Based On Cid

Design of IP Telephone Based on TMS320C5402

Design of Embedded CAN-ethemet Gateway Based on DSP

Design of TMS320F2812 Ethernet Interface Based on ENC28J60

Deterministic and Real-Time Communication over Ethernet in EPA Control System

Design and Realization of EtherNet Communication Node Based on C8051F02x Microcontroller

Implementation of Ethernet Communication of Power Quality Parameters

Ethernet Interface Design Based on TMS320VC5402 Digital Signal Process System

Design of Embedded Ethernet Data Transmission System Based on DSP

Application of W5100 in DSP Remote Ethernet Communication System

Design of Building Intercom System Based on Power Line Carrier