Design and Realization of the Ethernet Phone Based on SDA80D51

贾德胜,黄永峰

2005-01-01

Abstract:An Ethernet IP phone design was introduced in this paper. The design used SDA80D51 as the MCU and DSP unit to realize an efficient Ethernet phone. Some advice on the program of the MCU system was also given.

What problem does this paper attempt to address?

DESIGN AND REALIZATION OF HIGH PERFORMANCE-COST RADIO ETHERNET SIP PHONE WITH STUN SUPPORT

Luo Yanlin,Huang Yongfeng,Liu Xuehui

DOI: https://doi.org/10.3321/j.issn:0476-0301.2007.05.011

2007-01-01

Abstract:The design of high performance-cost radio ethernet SIP phone with STUN support is introduced.The design uses SDA80D51 as the MCU and DSP unit and RTL8019AS as the network interface.In consideration of the limited resources of embedded system,a SIP stack structure and STUN realization arithmetic fit for embedded system are designed and realized.Some skills and methods optimized the code and data storage are also given.
Design of IPPBX based on embedded system

Yuemei YANG,Pingshan CHEN,Dongqin FENG

DOI: https://doi.org/10.16652/j.issn.1004-373x.2015.12.022

2015-01-01

Abstract:With the packet exchange principle,IPPBX can realize the functions of the traditional PBX on Ethernet and overcome the insufficiency of traditional PBX effectively. It has powerful functions,comprehensive services with less cost. The typical networking mode of IPPBX is introduced in this paper. The design principles of each module system MPC8250 hardware system based on IPPBX and the software system of the system are given. The protocol conversion software of main con?trol module is also analyzed. The test result shows that the system can achieve simultaneous processing of 200 calls and its voice quality is excellent.
Design and Implementation of Distributed VoIP Architecture Based on SIP Protocol

张旭光,平玲娣,潘雪增

DOI: https://doi.org/10.3969/j.issn.1000-3428.2004.14.037

2004-01-01

Abstract:With the development of the Internet technologies and computer communication technologies, the traditionary circuit-switch based network must evolves to the new generation network which is based on the packet-switch technology. Facing the progress and status of the convergence of the three-networks, This document presents a distributed and SIP protocal based VoIP system prototype. Due to combinating of merits of SIP and IP, this model not only provides the interoperation with the existed network, but also provides an extendable plat for the NGN. This model uses private VoIP network to achieve the QoS.
A Design of Powered Device Interface Chip under PoE System

Long Fei Qi,Zhi Hua Ning,Le Nian He

DOI: https://doi.org/10.4028/www.scientific.net/amm.716-717.1277

2014-01-01

Applied Mechanics and Materials

Abstract:This paper proposes a design of powered device interface chip compatible with communication protocol IEEE 802.at standard, for Ethernet control of power supply. This design has all the features IEEE 802.at standard requires, including the detection, classification, under-voltage lockout and inrush current control, support of not less than 25.5W of power. The circuit of the chip is designed with Hangzhou Silan BCD process technique. Specific features of the design are 140mA inrush-current-limiting, complementary-output-enable-signal, under-voltage, overvoltage, over temperature protection, an optional external power adapter input, IEEE 802.3at type2 display signals by new electrical equipment, as well as two-event classification logic implementation.
The Design of MDF Remote Intelligent Supervisor System with S3C44B0X

LIN Ying-zi,XU Yuan-xin,WANG Kuang

DOI: https://doi.org/10.3969/j.issn.1671-7147.2005.03.007

2005-01-01

Abstract:MDF remote intelligent supervisor system reduces administrators redundance and facilitates concentrating management of the distributed switching offices,which monitors malfunction of the remote office and transfers the messages to the center office. This system adopted ARM7TDMI-S3C44B0X as main processor produced by SAMSUNG Corp. The communication method between center machine and the remote one is based on Ethernet. The paper elaborates the system scheme and the realization of network communication.
Design of IP Telephone Based on TMS320C5402

侯建军,柳立鹏,邵文龙

DOI: https://doi.org/10.3969/j.issn.1673-0291.2001.03.028

2001-01-01

Abstract:A DSP-based solution to LAN/Intranet-oriented IP telephone is presented. This IP Telephone can be used either as a desktop PC peripheral or as an Intranet network terminal. Its cores are TMS320C5402 in charge of voice code and MPC860T in charge of communications protocol processing and control logic. Several kinds of interface including USB, RS232 and RJ45 are designed to allow IP telephone to connect with other equipment in flexible ways. Some details of hardware architecture are discussed in this paper.
The Implementation and Performance Analysis of an Ethernet Embedded System Based on a Microcontroller

刘康,王宣银

DOI: https://doi.org/10.3969/j.issn.1000-0682.2004.01.010

2004-01-01

Abstract:This paper presents an ethernet controller consisting of the RTL8019AS and the implementing of the TCP/IP in an embeded microcontroller system,which usually has a limit memory space.The remote data communication between the user and the RS-485 field bus has been realized in this system along with the analysis of its performance.
The Design of Embedded Socket Software

ZHANG Han,FENG Dong-qin

DOI: https://doi.org/10.3969/j.issn.1000-0682.2007.02.016

2007-01-01

Abstract:This paper makes a study of the principle of an embedded UDP stack socket,and presents the design conception of the socket tasks run in the kernel of an embedded operation system along with the real-time application run in the socket task to ensure its real-time demand.These applications perform in an interface mode,which is different from the kernel mode and the user's mode in the embedded operation system.
Design and Realization of Conference System Based on IP Video Phone

熊平华,杨建刚

DOI: https://doi.org/10.3969/j.issn.1000-7024.2004.04.042

2004-01-01

Abstract:Beginning from the ITU H.323 multimedia communication protocol and the hardware and software architecture of a MCU system, a IP video phone conference system based on the H. 323 protocol was introduced, which is a embedded system de-signed for special requirement. To enhance the utilization performance of network resource, the grouping exchange technology was applied in the network layer in this system. It was specially put forward a double process boards hardware structure-the sup-port hardware for audio/video encode and decode, data encapsulate etc was integrated in the mother board and the communication function with the network in the subsidiary board. The two boards communicate with data stream mechanism and the software system was also drived by data stream. High reliability , low cost and good transplantation to the realization of IP video phone conference system were provided, which was meaningful used to reference by similar small video conference system research and development.
Design of embedded network interface based on ENC28J60

刘琼,朱志伟,周志光

DOI: https://doi.org/10.3969/j.issn.1008-0570.2008.14.124

2008-01-01

Abstract:A solution of ethernet interface based on the core of ENC28J60 and its architecture of hardware is illustrated. Following a brief introduction of the structure, functions and external connections of the ENC28J60.The solution how to make ENC28J60 communicate with Atmega16 are expatiated. This solution not only can reduce the cost but also can obtain the transmitted rate of 500Kbps,and can satisfy the requirements of controlling embedded system through Internet.
A method for communication between DSP and MCS-51 by SPI interface

蔡慧,赵荣祥,吴靖

DOI: https://doi.org/10.3969/j.issn.1003-188X.2004.06.096

2004-01-01

Abstract:This paper explains the possibility of communication between DSP and MCS-51, and analyzes characteristics and theory of SPI in detail. It mostly introduces the design method of hardware and software for extending SPI, and implements the interface of communication between DSP and MCS-51.
Reconfigurable Designs for Networking Silicon.

Tao Li,Zhentao Liu,Huimin Du,Lei Zhang,Jungang Han,Lin Jiang,Qingang Dong

DOI: https://doi.org/10.1109/ipdpsw.2012.35

2012-01-01

Abstract:This paper presents a reconfigurable architecture and associated design methodology for developing networking silicon chips. The tools include most of the common traffic QoS features and low level interfaces as well as some special features for extensible design. When coupled with the design tools, this architecture provides powerful capabilities for the design of highly flexible networking silicon IP cores.
Design and Implementation of LWIP Ethernet Based on SOPC AXI Bus

Xiong Shengjiang,Dai Wenwen,Yan Wei

2012-01-01

Abstract:In according with the wide use of Ethernet communication, this paper proposed a programmable system on chip (SOPC) technology, using the Xilinx Spartan-6 FPGA series XC6S LX16 chips, utilizing soft core MicroBlaze, basing on AXI bus. The system is implemented by function design method of LWIP protocol. It can complete the functions and aims of this project, and after testing the results indicate that the system running well.
Design of Central Processing Module of Baseband SoC for Digital Interphone

Chao ZHANG,Xiaokang LIN

DOI: https://doi.org/10.3969/j.issn.1002-8684.2012.01.008

2012-01-01

Abstract:DW8051 is a 8-bit microcontroller core that is instruction-set-compatible with the industry-standard 8051.An approach to the design of central processing module of baseband SoC for digital interphone is described.The architecture of baseband SoC and functions of the central processing module are analyzed firstly,and then a verification platform is designed to test whether low-end 8051 microcontroller meets work requirements of the system,finally design method and verification process for the central processing module based on DW8051 IP core are discussed in detail.
SOC Design of SMTE and System Realization

ZHANG Guo,ZHAO Yan,ZHANG Chun,WANG Zhi-hua,HUANGFU Li-ying,NING Yan-qing,HU Xue-liang

DOI: https://doi.org/10.3969/j.issn.1003-353x.2005.10.017

2005-01-01

Abstract:The achievement that SMS (short message service) thrived in GSM leads to the extension to PSTN (public switched telephone network). A SOC of SMTE (short message terminal equipment) is designed based on MCS51 compatible 8 bit MCU core. Dedicated DTMF, FSK transmitter and receiver using 1 bit quantification are presented. By this means, this design saves analog to digital converter, improves design reusability remarkably and reduces power consumption.
The New Dust Removal Controller Based on 80C196 Monochip with PSD Chip

Zhang Weiping

DOI: https://doi.org/10.3969/j.issn.1004-6429.2005.05.055

2005-01-01

Abstract:The article has introduced the designing plan of a kind of highly integrated hardware of the new electric dust removal controller, explained in detail some of its key composing unit, proposed a framework of "symmetric network" based on CAN bus and expounded a network designing philosophy to carry on information exchange and resource-sharing in the B/S mode adopting IPC system.
Design and realization of video conference MCU based on DM 8168

Bing LIU,Yuan-tao GU

DOI: https://doi.org/10.3969/j.issn.1000-7024.2014.10.011

2014-01-01

Abstract:An embedded video conference MCU based on TMS320DM8168 was designed and realized .G.722 algorithm was cho-sen for the speech compression ,H.264 algorithm was chosen for the video compression ,and RTP was used to transport media streams .The hardware solution and the software implementation were elaborated .The QoS for the video conference was also analyzed .Characterized by the small size and the low power ,the proposed system can provide service for 8 users at the same time .Test results show that the system has the advantage of high reliability ,smooth audio and video streams ,and its processing delay is less than 100 ms ,which can meet the performance requirements in the video conference .
The Design of GPRS System Based on S3C2410A

He Shi-jie,Zhang Chun,Wang Yan-hong

DOI: https://doi.org/10.3969/j.issn.1003-0107.2011.04.012

2011-01-01

Abstract:The GPRS communication system designed in this paper uses S3C2410A embedded processor and MC39i as the GPRS communication module.This paper designs hardware system,serial driver changes,PPP protocol application porting kit and GPRS communication program etc.,which can be used for wireless data transmission,environmental monitoring and other occasions.
Ethernet Communication Design of Embedded System Based on ARM

SHI Guang-zhi,LIU Bo,JIANG Xiu-jie,LIU Cheng

DOI: https://doi.org/10.3969/j.issn.2095-6835.2010.32.033

2010-01-01

Abstract:This paper introduces an embedded communication system based on ARM.The use of LPC2368 microcontroller chip and DP83848 physical chip are conducted to design the hardware,the transplant process of μC/OS-Ⅱ is accomplished to establish development environment,based on which designs the TCP/IP protocol and implements socket communication.The solution realizes data transmission of embedded communication system and has been applied successfully in the data collection and communication system of electric instrument.
Design and Application of FEC Driver in Embedded Systems

REN Xi-bo,JI Xiao-yong

DOI: https://doi.org/10.3969/j.issn.1002-2279.2005.06.024

2005-01-01

Microprocessors

Abstract:This paper first discusses the design of FEC driver,then implements a TFTP protocol client stack,which is successfully used in the bootloader program of embedded systems.The FEC driver discussed in this paper has some practical values.And This paper also provides a way to implement the embedded systems which need to connect to Ehternet.

Design and Realization of the Ethernet Phone Based on SDA80D51

DESIGN AND REALIZATION OF HIGH PERFORMANCE-COST RADIO ETHERNET SIP PHONE WITH STUN SUPPORT

Design of IPPBX based on embedded system

Design and Implementation of Distributed VoIP Architecture Based on SIP Protocol

A Design of Powered Device Interface Chip under PoE System

The Design of MDF Remote Intelligent Supervisor System with S3C44B0X

Design of IP Telephone Based on TMS320C5402

The Implementation and Performance Analysis of an Ethernet Embedded System Based on a Microcontroller

The Design of Embedded Socket Software

Design and Realization of Conference System Based on IP Video Phone

Design of embedded network interface based on ENC28J60

A method for communication between DSP and MCS-51 by SPI interface

Reconfigurable Designs for Networking Silicon.

Design and Implementation of LWIP Ethernet Based on SOPC AXI Bus

Design of Central Processing Module of Baseband SoC for Digital Interphone

SOC Design of SMTE and System Realization

The New Dust Removal Controller Based on 80C196 Monochip with PSD Chip

Design and realization of video conference MCU based on DM 8168

The Design of GPRS System Based on S3C2410A

Ethernet Communication Design of Embedded System Based on ARM

Design and Application of FEC Driver in Embedded Systems