Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Fatigue Crack Propagation in Polyethylene Methacrylate

Fatigue crack growth properties of PMMA material used in underwater transparent structures

Modeling the Effect of Physical Aging on the Stress Response of Amorphous Polymers Based on a Two-Temperature Continuum Theory

Comparison of the Fatigue Crack Propagation Behavior of Two Different Forms of Pmma Using Two-Stage Zone Model

A Monte Carlo Study Of The Glass Transition Of Polymethylene

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Shear-compression failure behavior of PMMA at different loading rates

A Local Stress Approach to Predict the Fatigue Life of the U-Notched Pmma Plate at Different Temperatures

Experimental Investigation of Dynamic Fracture Behaviors of Polymethyl Methacrylate

Experimental Study of Size Dependence of Fracture Toughness of PMMA

Weibull Statistical Analysis on Tensile Strength of Adhesive Joint in PMMA

A constitutive model for poly-methyl-methacrylate over a wide range of strain rates and temperatures

Modelling Fatigue Crack Growth in High-Density Polyethylene and Acrylonitrile Butadiene Styrene Polymers

A Novel Method for Characterizing the Fatigue Crack Propagation of Steel Via the Weak Magnetic Effect

Multi-crack Propagation in PMMA Plates under Dynamic Out-of-plane Impact

Damage Investigation in PMMA Polymer: Experimental and Phase-Field Approaches

Influence of Interfacial Bond Strength on Fatigue Life and Thermo-Mechanical Behavior of a Particulate Composite: An Experimental Study

Dynamic fracture testing of polymethyl-methacrylate (PMMA) single-edge notched beam

Experimental Investigation and Modeling of the Mechanical Properties of Construction PMMA at Different Temperatures

Experimental study of dynamic fracture behavior of PMMA with overlapping offset-parallel cracks

Experimental study and theoretical analysis of ECC type I fatigue fracture after subjected to sub-high temperature