Abstract:When the local heat flux exceeds specified flux limit, tungsten PFC surfaces can be damaged, which is not acceptable for a reliable reactor operations. The divertor PFCs are typically designed for a specific heat flux limit usually assuming an average steady-state heat flux which is typically 5–10 MW/m 2 . However, in addition to steady-state heat flux, fusion reactor divertor PFCs could experience transient heat fluxes such as ELMs and/or other magnetic reconnection events which can deposit large transient heat fluxes onto the divertor PFCs. The transient divertor heat flux could be significantly larger than the steady-state heat flux which could damage the solid PFC surfaces. The divertor heat flux can be subjected to additional complications such as the uncertainties in the the divertor strike point heat flux projection. Moreover, there are additional experimental observations of non-axisymmetric power flux which can occur under non-axisymmetric magnetic perturbations. The liquid lithium (LL) PFCs is more resilient against such transient heat fluxes as they could evaporate LL as needed and the lost LL can be then replenished afterward. In this paper, we analyze a case for a transient divertor heat pulse of 1 MJ in 10 ms for a ITER-size reactor. This is a small perturbation (~ 0.1%) to the expected plasma stored energy compared to the previously analyzed case of 20 MJ heat pulse. Even with this relatively modest heat pulse, the LL surface undergoes ~ 100 °C temperature rise. However, the resulting LL surface heating without rapid cooldown mechanism could lead to excessive LL evaporation continuing well after the transient heat flux resulting in a significant Li injection of ~ 0.6 mol in about a 200 ms period. This amount of Li injection could cause plasma dilution and performance degradation. On the other hand, an active Li injection capability if optimized could prevent the LL surface temperature rise and thus reducing subsequent Li evaporation into the plasma by a factor of 7 compared to the passive LL PFC case. A crucial tool of active Li injection is a rapid response pellet injector which could inject light impurity pellets before the excessive heat flux could reach the divertor plate causing serious damage. A simple pellet ablation model suggests a favorable pellet deposition profile for smaller ~ 0.1 mm radius pellet with ~ 10–20 m/s velocity. Moreover, if it is possible to inject from the private flux region, the pellet injection efficiency into the high heat flux strike point region can be as high as 80% compared to ~ 50% for the injection from outer radius region. The pellet deposition efficiency can be further improved by designing a shell-pellet which can burst when a certain ablation fraction is reached. A possible implementation technique using an inductive pellet injector with a rapid time response of a few msec is proposed here which can be tested in NSTX-U.

Rapid Global Response of the Electron-Temperature During Pellet Injection on Tore-Supra

Recent Experiment Results During Electron Cyclotron Heating On Hl-2a

Pellet Enhanced Performance on the Hl-2a Tokamak

Analysis of electron heat transport with off-axis modulated ECRH in Tore Supra

Electron Temperature Gradient Turbulence: Validation in the Columbia Linear Machine Experiments

Electron Transport in Tore Supra with Fast Wave Electron Heating

Achieving Temporary Divertor Plasma Detachment with MARFE Events by Pellet Injection in the EAST Superconducting Tokamak

Non-linear shattered pellet injection modelling in ASDEX Upgrade

Hot-tail Electrons' Impact on Assimilation and Injection Penetration of D2 Shattered Pellet Injections

Drift of ablated material after pellet injection in a tokamak

Advanced Simulation of Electron Heat Transport in Fusion Plasmas

Experimental Determination of Critical Threshold in Electron Transport on Tore Supra.

Ion Temperature Measurements in the MAST-U Divertor During Steady State Plasmas and ELM Burn Through Phenomena

Active Lithium Injection for a Real Time Control of the Divertor Heat Flux for Fusion Devices

Study of the Evolution of Density and Particle Transport During Density Relaxation Phase after Pellet Fueling on the EAST Tokamak

Electron Temperature Fluctuations Correlated with Energy Confinement Degradation in the EAST Ohmic Plasmas

Ultra-fast charge exchange spectroscopy for turbulent ion temperature fluctuation measurements on the DIII-D tokamak (invited)

Radiation asymmetry and MHD destabilization during the thermal quench after impurity Shattered Pellet Injection

Direct Measurement of the Electron Turbulence-Broadening Edge Transport Barrier to Facilitate Core–edge Integration in Tokamak Fusion Plasmas

Electron Injections from A Floated Plate into A Collisionless Plasma

Ion temperature gradient mode mitigation by energetic particles, mediated by forced-driven zonal flows