Abstract:Copper oxide was synthesis by hydrothermal method using copper nano powder (30nm) and deionized water on quartz substrate. At temperature 100 °C, different experimental time ranging from (24–72 h). Different copper oxide phase was presented in X-Ray diffraction analyzer, the crystal size increased as the reaction time increased as it calculated using scherrer equation to be (21.1–32.03 nm), and Williamson Hall plot to be (40.3–87.7 nm). Also, Raman spectroscopy show different copper phase and the highest intensity peak at 220 cm −1 , due to the cuprous oxide in all sample used to distinct chemical fingerprint for a particular molecule or material. Many of metal oxide bond was study by FTIR to clarify the compositional and chemical properties of the prepared samples. Optical characteristic with different absorption peaks of thin film show decrease in the band gap from (2.8–2.4 eV) as the reaction time increase. PL measurement used also to determine the band gap energy of the prepared thin film which found to be agreement with UV–Vis, and the band gap value is (2.7, 2.6, 2.5, 2.3, and 2.3 eV), respectively. Increasing in the surface roughness from (3.637–25.16 nm), and in the root mean square from (5–29.39 nm), and grain size with increasing the reaction time from (24–72 h), respectively, was measured by using AFM technique. Different morphologies were showed with increasing the reaction time, spherical and truncated octahedral in different type was obtained by field emission-scanning electron microscope (FE-SEM) as the particles subject to transformation caused the preparing agglomerated crystallites. The electrical characteristic was analysis use DC measurement to measure the activation energy which varied with reaction time. The figure of merit analysis shows that the copper oxidation state to obtain cuprous oxide (Cu 2 O) is mainly obtained at the 48 h-reaction time. The used of copper nano powder in hydrothermal method without adding any auxiliary material the main aim of this research.

Effect of Processing Conditions on Sonochemical Synthesis of Nanosized Copper Aluminate Powders.

The Convenient Preparation of Porous CuO Via Copper Oxalate Precursor

Morphology Control Of Cuo Micro-Particles Using Zn2+ Ion And Ultrasonic Treatment

Effect of co-precipitation synthesis parameters on gadolinium aluminate nanoparticles

Sonochemical Synthesis and Characterization of Spinel CoAl2O4 Nanoparticles

Effect of reaction condition on microstructure and properties of (NiCuZn)Fe2O4 nanoparticles synthesized via co-precipitation with ultrasonic irradiation

Hydrothermal Preparation of CuAlO2 Powder

Effect of Synthesis Conditions on CuO-NiO Nanocomposites Synthesized via Saponin-Green/Microwave Assisted-Hydrothermal Method

Influence of impurities on the sintering densification in nano- Al2O3 powders coated by copper

Sonochemical Synthesis of Copper Borates: Effect of Reaction Conditions on the Characteristic Properties

Influence of Ultrasonic Irradiation on the Microstructure of Cu/Al2O3, CeO2 Nanocomposite Thin Films During Electrocodeposition

Controllable Preparation Conditions of Monodisperse γ-Al2O3 Nanoparticles

Preparation of Copper Nanoparticles by Radiation

Optical and structural properties of spherical-shaped boehmite and γ-alumina nanoparticles by ultrasonic-assisted hydrothermal method: the effects of synthesis route, calcination, and precursor concentration

Microwave-Induced Polyol-Process Synthesis of Copper and Copper Oxide Nanocrystals with Controllable Morphology

Preparation and Phase Transformation of Nanocrystalline Copper Sulfides (cu9s8, Cu7S4 and CuS) at Low Temperature

Deposition time effect on copper oxide nano structures, an analysis study using chemical method

High Purity Copper Nanoparticles Via Sonoelectrochemical Approach

Controllable Synthesis and Characterization of Spindle-Like CuO Micro-structure

Preparation of YAG Nano-Powders Via an Ultrasonic Spray Co-Precipitation Method

Ultrasound As a Tool to Synthesize Nano-Sized Silica–Alumina Catalysts with Controlled Mesoporous Distribution by a Novel Sol–Gel Process