Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Multi-dimensional Numerical Simulation of Operating Process of CNG Engine Using Detailed Chemical Kinetics with CFD

Numerical Simulation of HCCI Engine with Multi-Stage Gasoline Direct Injection Using 3D-CFD with Detailed Chemistry

Multidimensional Computational Fluid Dynamics Combustion Process Modeling of a 6V150 Diesel Engine

Multi-dimensional simulation of HCCI engine using parallel computation and chemical kinetics

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Numerical Simulation of Gasoline Stratified Charge Compression Ignition Using 3D-CFD Coupled with Detailed Chemistry

Three-Dimensional Computational Fluid Dynamics Modeling of a 6V150 Diesel Engine

Numerical Simulation for Combustion of Droplet with Volume of Fluid Formulation

Numerical Methods for Complicated Chemical Mechanism Involved in Combustion Simulation

Multi-Dimensional Simulation of HCCI Engine Using Parallel Computation and Reduced Mechanisms

Simulation of In-Cylinder Radiative Heat Transfer of Diesel Engine with Monte-Carlo Method

Multi-dimensional Simulation Study of an HCNG Engine

A Transport Equation Residual Model Incorporating Refined G-Equation and Detailed Chemical Kinetics Combustion Models

An Advanced High Dimensional Model Representation Approach for Internal Combustion Engine Modeling and Optimization

Experimental Investigation and Numerical Modeling of Spray Combustion and Emission in a Diesel Engine

Multi-Scale Simulation of Biomass Gasification in Fluidized Beds

Numerical Simulation and Experiment for Soot and NOx Emission in Diesel Engine

3D Numerical Simulation for Gasoline HCCI Engine with Two-Stage Injection Based on Parallel Computation

Numerical Simulation of HCNG Engine on GT-Power

Simulation on the Combustion System Work Process for Internal Combustion Engine by Using KIVA-3V.

3D Numerical Simulation of Spray and Combustion Process for In-cylinder DI Gasoline Engine