Abstract:Ultrahigh molecular weight polyethylene (UHMWPE) is injection molded under high pressure and studied by ultra-small-angle X-ray scattering (USAXS) during melting in a time-resolved synchrotron radiation experiment. Results concerning melting and recrystallization of crystalline lamellae are compared to data obtained by differential scanning calorimetry (DSC). USAXS analysis reveals a coupled process of melting and crystallization which is not accompanied by external heat flow. Nine isotropic samples differing in molecular weight and molding pressure are heated at a rate of 5 degreesC/min. 2D USAXS images integrate over temperature intervals between 3 and 7 degreesC. The materials are considered two-phase semicrystalline polymers. Scattering curves obtained by azimuthal averaging are transformed to interface distribution functions (IDF) which are perfectly Fitted by a nanostructural model comprising an ensemble of thick, uncorrelated layers (50 nm thickness) and stacks of short-range correlated crystalline lamellae (20 nm). Crystalline layers are identified from their narrower layer thickness distribution and their melting behavior, After the scattering effect of amorphous layers is eliminated, a composite crystallite thickness distribution is obtained. Its variation is studied as a function of temperature, molecular mass and molding pressure. In DSC thermograms samples prepared at high pressure exhibit a single strong melting peak, whereas the other samples show an additional melting peak at lower temperature. This might lead to the conclusion that the high-pressure samples predominantly contain extended chain crystals. USAXS shows that high-pressure materials contain considerable amounts of imperfect thin crystal lamellae that melt at lower temperature, while thick lamellae are formed. With low-pressure samples, this coupled process of nanostructure transformation during annealing is found to be negligible.

Studies on the Free-Volume Change in Annealed Ultra-High Molecular Weight Polyethylene by the Positron Annihilation Technique

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

Preparation of Microporous Ultra High Molecular Weight Polyethylene (uhmwpe) by Thermally Induced Phase Separation of A Uhmwpe/Liquid Paraffin Mixture

Polymorphic Transition in Disordered Poly(l-lactide) Crystals Induced by Annealing at Elevated Temperatures

Nanostructure Evolution of Isotropic High-Pressure Injection-Molded Uhmwpe During Heating

Studies On The Nature Of The Macromolecular Condensed State Of "Nascent" Ultra High Molar Mass Polyethylene

Effects of Annealing on the Hierarchical Crystalline Structures and Mechanical Properties of Injection‐molded Bars of High‐density Polyethylene

Sintering evolution monitoring of ultra‐high‐molecular‐weight polyethylene

Study of the Fine Crystalline Structure of Polyethylenes Via Annealing and Thermal Fractionation

Annealing of melt-crystallized polyethylene and its influence on microstructure and mechanical properties: A comparative study on branched and linear polyethylenes

Inverse Temperature Dependence of Strain Hardening in Ultrahigh Molecular Weight Polyethylene: Role of Lamellar Coupling and Entanglement Density

The Isothermal Melting Kinetics of Ultrahigh Molecular Weight Polyethylene Crystals

Annealing Effects on the Tree Initiation Voltage of Polyethylene at High Temperature

Deformation of Ultrahigh Molecular Weight Polyethylene Precursor Fiber: Crystal Slip with or Without Melting

The influence of UHMWPE with varying morphologies on the non-isothermal crystallization kinetics of HDPE

Melting Behavior and Morphology of Freeze-Dried Ultra-High Molar Mass Polyethylene

In Situ Fourier Transform Infrared Spectroscopic Study of the Conformational Changes of High‐density Poly(ethylene) During the Melting and Crystallization Processes

Effect of Annealing on Fracture Behavior of Poly(propylene‐block‐ethylene) Using Essential Work of Fracture Analysis

Effects of Heating, Tensile, and High Pressure Treatments on Aggregate Structure of a Low Density Polyethylene

Studies of UHMWPE gel crystallizing films by small-angle X-ray diffraction

Effect of Crystallization Conditions on Melt Recrystallization Behavior of PE-UHMW