Simulation Analysis on Nebulizing Effects of Supersonic Atomizer Adapted to Ventilator

XU Xin,WANG Xiao-hai

DOI: https://doi.org/10.3969/j.issn.1674-1633.2007.06.004

2007-01-01

Abstract:Describes the improving method for the structure of 402A medical supersonic atomizer which can be adapted to ventilators.Studies the possible contributions on nebulizing effects of the atomizer when adapted to ventilators by homogeneous design.

What problem does this paper attempt to address?

Numerical Comparison of the Efficiency of Mixing Ventilation and Impinging Jet Ventilation for Exhaled Particle Removal in a Model Intensive Care Unit

Lei Wang,Xiahong Dai,Jianjian Wei,Zhengtao Ai,Yifan Fan,Lingling Tang,Tao Jin,Jian Ge

DOI: https://doi.org/10.1016/j.buildenv.2021.107955

IF: 7.093

2021-01-01

Building and Environment

Abstract:Effective infection prevention and control measures are required in the intensive care units of hospitals, as these areas have a high incidence of nosocomial infections. Adopting proper ventilation pattern that is efficient in pollutant removal is important for controlling the spread of infectious diseases. In this study, the computational fluid dynamics (CFD) simulation approach is used to investigate the airflow pattern, fates of respiratory particles, and patients' intake fraction in a four-bed model intensive care unit under three types of ventilation: impinging jet ventilation and two forms of mixing ventilation. The results show that in contrast to mixing ventilation, the airflow trend of impinging jet ventilation is consistent with the thermal plume of the human body. Accordingly, impinging jet ventilation can efficiently remove pollutants at the ceiling level, thereby reducing cross-infection. Our results also show that fine particles are greatly affected by the ventilation pattern, whereas large particles are primarily removed by surface deposition. The maximum intake fraction of susceptible patients under the three types of ventilation are 8.24 x 10-5 (impinging jet ventilation); 4.5 x 10-4 (ceiling air ventilation; a type of mixing ventilation) and 5.3 x 10-4 (side air ventilation; a type of mixing ventilation). Impinging jet ventilation appears to be the most effective ventilation system for removing particles and reducing susceptible patients' intake fraction under our investigated scenarios, and exhibits great potential as a ventilation method in intensive care units.
Three-Dimensional Simulation Of Effervescent Atomization Spray

Hong-Bing Xiong,Jian-Zhong Lin,Ze-Fei Zhu

DOI: https://doi.org/10.1615/AtomizSpr.v19.i1.50

IF: 1.134

2009-01-01

Atomization and Sprays

Abstract:A comprehensive three-dimensional model of droplet-gas two-phase flow is presented to examine the evolution of spray along the downstream of the exit orifice in an effervescent atomizer. For gas phase, the Navier-Stokes equations with k-epsilon turbulence model are solved, considering two-way coupling of the interaction between droplets and the gas phase. The dispersed droplet phase is modeled as Lagrangian entities, accounting for the physical phenomena of droplet generation from primary and secondary breakup, droplet collision and coalescence, droplet momentum, and heat transfer. This model is used to calculate the mean size and statistical distributions of atomized droplets under various operating conditions such as air-to-liquid ratio (ALR), injection pressure, liquid flow rate, nozzle exit diameter, and liquid material. The simulation results compare well with the experimental data, with an accuracy of 5% for the atomizer operated under annular flow conditions. Gas flow and spray evolution of the droplets are predicted; effects of operating conditions on the droplet mean size and distributions are discussed. Results show that ALR is one of the most important control parameters. Increasing ALR will decrease the droplet size gradually and finally tend to a certain limitation. A decreasing nozzle exit favors primary breakup, while high injection pressure has more influence on the secondary atomization. An increasing liquid mass flow rate has better primary breakup and worse overall atomization downstream. The liquid properties also have great impact on the droplet atomization. The less the viscosity and surface tension, the easier liquid breaks into smaller drops.
Optimization of Vibrating Mesh Nebulizer Air Inlet Structure for Pulmonary Drug Delivery

Yu Liu,Xiaole Chen,Zhengqi Li,Huizhen Yang,Jianwei Wang

DOI: https://doi.org/10.3390/atmos14101509

IF: 3.11

2023-09-30

Atmosphere

Abstract:The vibrating mesh nebulizer (VMN) has gained popularity for its compactness and noiselessness. This study investigates the impact of different air inlet structures on the deposition fraction (DF) of droplets generated by VMNs in an idealized mouth–throat (MT) airway model. Three homemade VMNs with semi-circular inlet, symmetrical four-inlet, and multiple-orifice inlet structures were evaluated through simulations and experiments. The changes in droplet DF of 0.9% w/v concentration of nebulized sodium chloride (NaCl) droplets as a function of inertial parameters were acquired under different inhalation flow conditions. Additionally, flow field distributions in models with different inlet structures were analyzed at a steady inspiratory flow rate of 15 L/min. The results indicate that optimizing the VMN's air inlet structure significantly enhances droplet delivery efficiency. The multiple–orifice inlet structure outperformed the other designs, directing the airflow from the inlet position to the center of the mouthpiece and then into the oral cavity, achieving a DF of up to 20% at an inhalation flow rate of 15 L/min. The region of high airflow velocity between the mouthpiece and oral cavity proved to be a favorable VMN inlet optimization, reducing direct droplet–wall collisions and improving delivery efficiency. These findings offer insights for VMN design and optimization to enhance pulmonary drug delivery effectiveness and therapeutic outcomes.

environmental sciences,meteorology & atmospheric sciences
Simulation of Effervescent Atomization and Nanoparticle Characteristics in Radio Frequency Suspension Plasma Spray

Hong-Bing Xiong,Li-Juan Qian,Jian-Zhong Lin

DOI: https://doi.org/10.1007/s11666-011-9714-1

IF: 2.839

2012-01-01

Journal of Thermal Spray Technology

Abstract:In this paper, a comprehensive model was developed to investigate the suspension spray for a radio frequency (RF) plasma torch coupled with an effervescent atomizer. Firstly, the RF plasma is simulated by solving the thermo-fluid transport equations with electromagnetic Maxwell equation. Secondly, primary atomization of the suspension is solved by a proposed one-dimensional breakup model and validated with the experimental data. Thirdly, the suspension droplets and discharged nanoparticles are modeled in Lagrangian manner, to calculate each particle tracking, acceleration, heating, melting and evaporation. Saffman lift force, Brownian force and non-continuum effect are considered for nanoparticle momentum transfer, as well as the effects of evaporation on heat transfer. This model predicts the nanoparticle trajectory, velocity, temperature and size in the RF suspension plasma spray. Effects of the torch and atomizer operating conditions on the particle characteristics are investigated. Such operating conditions include gas-to-liquid flow ratio, atomizer orifice diameter, injection pressure, power input level, plasmas gas flow rate, and powder material. The statistical distributions for the multiple particles are also discussed for different cases.
Simulation of Droplet-gas Flow in the Effervescent Atomization Spray with an Impinging Plate

Lijuan QIAN,Jianzhong LIN,Hongbing XIONG

DOI: https://doi.org/10.1016/S1004-9541(09)60026-4

IF: 3.8

2009-01-01

Chinese Journal of Chemical Engineering

Abstract:A comprehensive three-dimensional model of droplet-gas flow was presented to study the evolution of spray in the effervescent atomization spray with an impinging plate. For gas phase, the N-S equation with the k-ɛ turbulence model was solved, considering two-way coupling interaction between droplets and gas phase. Dispersed droplet phase is modeled as Lagrangian entities, accounting for the physics of droplet generation from primary andsecondary breakup, droplet collision and coalescence, droplet momentum and heat transfer. The mean size and statistical distribution of atomized droplets at various nozzle-to-plate distances were calculated. Some simulation results were compared well with experimental data. The results show that the existence of the impinging plate has a pronounced influence on the droplet mean size, size distribution and the droplet spatial distribution. The air-to-liquid ratio has obvious effects on the droplet size and distribution.
Dissecting the performance of a jet nebulizer: The effect of changing design parameters and operating conditions

Harshit Soni,Ben Beaudry,Jennifer O'Neil,Larry Villasmil-Urdaneta

DOI: https://doi.org/10.1080/02786826.2024.2338520

2024-05-23

Aerosol Science and Technology

Abstract:Gas-powered jet nebulizers deliver medications to treat acute and chronic respiratory diseases. Several authors have found large variations in the performance of these nebulizers, and despite numerous attempts, deposition efficiency remains low for both adults and pediatrics. Using a Sympatec laser diffraction system and computational fluid dynamics (CFD) simulations with SolidWorks Flow Simulations and Ansys Fluent, this study uses a comparative analysis to explore the influence of supply air pressure, nozzle orifice diameter, and baffle geometry on jet nebulizer performance. Performance was quantified using critical performance metrics including vacuum levels driving aerosolization rate, Mass Median Aerodynamic Diameter (MMAD), and aerosolization time. Preliminary findings suggest that the authors' 2.54 mm wide, semi-conical bar baffle may produce superior vacuum levels, and surpasses the performance of the leading commercial bar baffle geometry, the SideStream, with a smaller MMAD (1.7 versus 2.3 microns). The study confirms the predicted relationship between supply pressure and nebulizer performance: higher pressure improves airflow rates, jet velocities, and aerosol characteristics, and reduces aerosolization times. Additionally, a larger nozzle orifice diameter increases airflow rates and promotes better aerosol characteristics, highlighting a direct correlation between orifice size and nebulizer performance. This work underscores the importance of expanding research in nebulizer performance beyond the traditional focus on testing paired nebulizer/compressor systems. Copyright © 2024 American Association for Aerosol Research

environmental sciences,meteorology & atmospheric sciences,engineering, chemical, mechanical
Effects of different mesh nebulizer sources on the dispersion of powder formulations produced with a new small-particle spray dryer

Ghali Aladwani,Mohammad A M Momin,Benjamin Spence,Dale R Farkas,Serena Bonasera,Amr Hassan,Michael Hindle,Worth Longest

DOI: https://doi.org/10.1016/j.ijpharm.2023.123138

2023-07-25

Abstract:The objective of this study was to explore the aerosolization performance of powders produced with different mesh nebulizer sources in the initial design of a new small-particle spray dryer system. An aqueous excipient enhanced growth (EEG) model formulation was spray dried using different mesh sources and the resulting powders were characterized based on (i) laser diffraction, (ii) aerosolization with a new infant air-jet dry powder inhaler, and (iii) aerosol transport through an infant nose-throat (NT) model ending with a tracheal filter. While few differences were observed among the powders, the medical-grade Aerogen Solo (with custom holder) and Aerogen Pro mesh sources were selected as lead candidates that produced mean fine particle fractions <5 µm and <1 µm in ranges of 80.6-77.4% and 13.1-16.0%, respectively. Improved aerosolization performance was achieved at a lower spray drying temperature. Lung delivery efficiencies through the NT model were in the range of 42.5-45.8% for powders from the Aerogen mesh sources, which were very similar to previous results with a commercial spray dryer. Ultimately, a custom spray dryer that can accept meshes with different characteristics (e.g., pore sizes and liquid flow rates) will provide particle engineers greater flexibility in producing highly dispersible powders with unique characteristics.
Numerical Simulation of the Nebulizer with Multiple Orifices

Zexuan Chen,Daniela Butan,Seamus Clifford,Russell Greaney,Sean Cunningham,Philip Griffin

DOI: https://doi.org/10.1088/1361-6439/ad6779

2024-07-27

Journal of Micromechanics and Microengineering

Abstract:A vibrating mesh nebulizer is a medical device that can break liquid medication into an aerosol of tiny droplets so that patients can inhale them to treat diseases. The volumetric flow rate of this kind of nebulizer is determined by many factors, including the orifice geometry, the vibration amplitude and the vibration mode shape. Thus, many experiments were designed to assess the effects of these different variables on flow rate and to find the optimal set of device parameters that maximises the flow rate. However, it can be very expensive to perform such physical experimentation with physical prototypes, which needs different orifice geometries to be fabricated for different test regimes. The orifice sizes are microscopic with diameters typically between 3 μm to 5 μm, thus, they are difficult to be fabricated with the exact shape and diameter that are required. Therefore, virtual prototyping by means of numerical simulation models are required as the orifice geometries and other factors can be easily changed in the simulation models. This study aims to provide a numerical simulation model that is experimentally validated. By comparing the simulated flow rates with the experimentally obtained flow rates, and the simulated droplet diameters with the experimentally obtained droplet diameters, it was found that the errors are all less than 10% which demonstrates this numerical simulation model is adequately validated by experiment. Thus, instead of carrying out expensive experiments, this simulation model can be used for predicting the volumetric flow rates for different prescribed orifice geometries. Furthermore, this paper also simulates the effects of viscosity and surface tension on the flow rate, where either viscosity or surface tension increases, the flow rate will decrease.

nanoscience & nanotechnology,engineering, electrical & electronic,instruments & instrumentation,physics, applied
Study on influencing factors of patients accepting Ventavis ultrasonic atomizing inhalation

Li Jun,Xu Zhuoming,Bian Jun

DOI: https://doi.org/10.3969/j.issn.1009-6493.2009.21.004

2009-01-01

Chinese Nursing Research

Abstract:Objective:To probe into the influencing factors of atomizing generator,tidal volume,drug concentration of ventilator under the mode of pressure-regulated volume control on Ventavis consumption rate,so as to find reasonable parameter setting,to reduce the residual of Ventavis after atomizing inhalation,and to enhance both drug utilization and cost profit.Methods:Mimical breathing circuit was connected with ventilator,test lung,Ventavis,atomizing generator. And Ventavis residual after atomizing inhalation under specific parameter of each group had been observed. Then each experiment had been repeated three times under the same parameter to reduce the error. Results:Through the experiment,we concluded that atomizing generator,tidal volume and body weight of infants have some influences on the Ventavis residual after atomizing inhalation. However,the frequency and time of breathing,the concentration of atomization liquid have no significant influence on the Ventavis residual after atomizing inhalation. Conclusion:It found out influencing factors of the drug consumption rate of Ventavis in atomizing inhalation. It provided some references for enhancing clinical maximum utilization of Ventavis aerosol inhalation and reducing cost at present. It offered some evidence for further exploring mathematical model for studying Ventavis consumption under special condition.
Effects of operating conditions on droplet deposition onto surface of atomization impinging spray

Jianzhong Lin,Lijuan Qian,Hongbin Xiong,Tat Leung Chan

DOI: https://doi.org/10.1016/j.surfcoat.2009.01.009

IF: 4.865

2009-01-01

Surface and Coatings Technology

Abstract:A comprehensive model based on the Navier–Stokes equation and particle tracking method is used to study the effervescent atomization impinging spray, and another model is used to establish the relationship between the droplet velocity near the plate and the different operating conditions. The models and numerical code are validated by comparing the numerical results with the published experimental results. The effects of air-to-liquid ratio, nozzle diameter, liquid mass flow rate, and the position of impinging plate on the Weber number and K number as well as the droplet deposition onto the plate are discussed. The results show that the droplet velocity near the plate increases with increasing air-to-liquid ratio and liquid mass flow rate, and with decreasing nozzle diameter and axial distance from the nozzle exit to the plate. The droplet diameter near the plate increases with increasing axial distance from the nozzle exit to the plate, and with decreasing air-to-liquid ratio. As a function of the nozzle diameter and liquid mass flow rate, the variation of droplet diameter is not monotonous and the effect of liquid mass flow rate on the droplet diameter is insignificant. In the studied operating conditions, it is difficult for the droplet to rebound off the plate when impinging on the plate but it is easier for the droplet to splash. In order to create a condition which can benefit the droplet deposition when impinging on the plate, the suggested ways are to reduce the air-to-liquid ratio and liquid mass flow rate, increase the nozzle diameter, and select a suitable range of axial distance from the nozzle exit to the plate.
Numerical Simulation of Effect of Various Parameters on Atomization in an Annular Slit Atomizer

Yi Wang,Yi-chen Dang,Xiao-qing Chen,Bao Wang,Zhong-qiu Liu,Jian-an Zhou,Chang-yong Chen

DOI: https://doi.org/10.1007/s42243-023-00943-3

2023-01-01

Journal of Iron and Steel Research International

Abstract:As the width–thickness ratio of the discrete nozzle atomizer's discrete hole greatly influences the loss of atomizing gas flow rate, the discrete nozzle atomizer was transformed into an annular slit atomizer with the same total nozzle outlet area. A numerical simulation study on the effect of various parameters on the atomization in the annular slit atomizer was carried out by coupling both the large eddy simulation (LES) and volume of fluid (VOF) model, which is based on the applicability of LES in capturing the breakup behavior of transient liquid droplets and the advantage of VOF method in directly capturing the phase interface. The simulation results showed that the increase in the atomization pressure makes the gas gain higher momentum, while the increase in the nozzle intersection angle decreases the distance between the nozzle exit and the computational domain axis. The increase in these two variables results in enhancing the gas–liquid interaction in the primary atomization zone and the formation of more aluminum droplets simultaneously. It is considered that the atomization effect becomes better when atomization pressure is 2.5 MPa, and the nozzle intersection angle is 60°. Industrial tests showed that the aluminum powder prepared by the optimized annular slit atomizer has a finer mean particle size and a higher yield of fine powder. The numerical simulation results agree well with the industrial test data of the powder particle size.
Aerosol Delivery to Simulated Spontaneously Breathing Tracheostomized Adult Model With and Without Humidification

Fai A Albuainain,Jie Li,Fai AlBuainain

DOI: https://doi.org/10.4187/respcare.11495

2024-03-14

Respiratory Care

Abstract:BACKGROUND: Optimal aerosol delivery methods for spontaneously breathing patients with a tracheostomy remain unclear. Thus, we aimed to assess the impact of nebulizer placement, flow settings, and interfaces on aerosol delivery by using a vibrating mesh nebulizer and a jet nebulizer in line with unheated humidification.METHODS: An 8.0-mm tracheostomy tube was connected to the lung model that simulates adult breathing parameters via a collecting filter. Albuterol sulfate (2.5 mg/3 mL) was administered via a vibrating mesh nebulizer and a jet nebulizer, which was placed in line with unheated humidification provided by a large-volume nebulizer, with FIO2 set at 0.28, with gas flows of 2 L/min versus 6 L/min. Nebulizers were placed in line distal and proximal to the lung model by using a tracheostomy collar and a T-piece. Conventional nebulization was tested using a vibrating mesh nebulizer and a jet nebulizer directly connected to the tracheostomy tube bypassing the humidification device. The drug was eluted from the collecting filter and assayed with ultraviolet spectrophotometry (276 nm).RESULTS: During in-line nebulizer placement with unheated humidification, the inhaled dose was 2-4 times higher with a gas flow of 2 L/min than 6 L/min, regardless of nebulizer type, placement, or interface (all P < .05). At 6 L/min, the inhaled dose was higher with proximal than distal placement when using both interfaces, but, at 2 L/min, the inhaled dose was lower with proximal placement. With a jet nebulizer, the tracheostomy collar generated a higher inhaled dose at proximal placement compared with the T-piece, whereas the T-piece resulted in a higher inhaled dose than the tracheostomy collar with distal placement, regardless of the flow settings. Compared with conventional nebulization using a vibrating mesh nebulizer, an in-line vibrating mesh nebulizer with a large-volume nebulizer at 2 L/min had a similar inhaled dose, regardless of nebulizer placement and interface. In contrast, the in-line jet nebulizer was influenced by both placement and interface.CONCLUSIONS: Aerosol delivery with an in-line vibrating mesh nebulizer and jet nebulizer with unheated humidification was affected by nebulizer placement, interface, and gas flow settings.

respiratory system,critical care medicine
Multi-Physics Coupled Acoustic-Mechanics Analysis and Synergetic Optimization for a Twin-Fluid Atomization Nozzle

Wenying Li,Yanying Li,Yingjie Lu,Jinhuan Xu,Bo Chen,Li Zhang,Yanbiao Li

DOI: https://doi.org/10.1186/s10033-024-01037-1

IF: 2.964

2024-05-23

Chinese Journal of Mechanical Engineering

Abstract:Fine particulate matter produced during the rapid industrialization over the past decades can cause significant harm to human health. Twin-fluid atomization technology is an effective means of controlling fine particulate matter pollution. In this paper, the influences of the main parameters on the droplet size, effective atomization range and sound pressure level (SPL) of a twin-fluid nozzle (TFN) are investigated, and in order to improve the atomization performance, a multi-objective synergetic optimization algorithm is presented. A multi-physics coupled acoustic-mechanics model based on the discrete phase model (DPM), large eddy simulation (LES) model, and Ffowcs Williams-Hawkings (FW-H) model is established, and the numerical simulation results of the multi-physics coupled acoustic-mechanics method are verified via experimental comparison. Based on the analysis of the multi-physics coupled acoustic-mechanics numerical simulation results, the effects of the water flow on the characteristics of the atomization flow distribution were obtained. A multi-physics coupled acoustic-mechanics numerical simulation result was employed to establish an orthogonal test database, and a multi-objective synergetic optimization algorithm was adopted to optimize the key parameters of the TFN. The optimal parameters are as follows: A gas flow of 0.94 m 3 /h, water flow of 0.0237 m 3 /h, orifice diameter of the self-excited vibrating cavity (SVC) of 1.19 mm, SVC orifice depth of 0.53 mm, distance between SVC and the outlet of nozzle of 5.11 mm, and a nozzle outlet diameter of 3.15 mm. The droplet particle size in the atomization flow field was significantly reduced, the spray distance improved by 71.56%, and the SPL data at each corresponding measurement point decreased by an average of 38.96%. The conclusions of this study offer a references for future TFN research.

engineering, mechanical
Experimental and Numerical Simulation Studies on the Atomization Characteristics of the Internal Mixing Nozzle and Its Field Application

Wenpu Li,Yiyi Zheng,He Shao,Xin Wang,Xi Chen,Yurong Gao

DOI: https://doi.org/10.1007/s42461-024-00955-x

2024-03-09

Abstract:This study utilized experimental and numerical simulation methods to investigate and analyze the atomization characteristics of three internal air–water mixed atomizers under different operating conditions. By comparing the research results, the effective dust control working parameters for the application of the selected atomizer in the engineering field were determined. Firstly, the atomization characteristics of the three atomizers were studied using a customized experimental system. The results indicated that nozzle 2 had a wide atomization range, a small atomization distance, and small droplet size; nozzle 3 had a narrow atomization range, large droplet size, and fast atomization speed; and nozzle 1 not only had a large atomization range but also could produce droplets of dry mist size with fast atomization speed, meeting the dust reduction requirements of the Majiliang Coal Preparation Plant. Secondly, Fluent software was used to simulate the atomization process and particle size distribution of the three internal mixed atomizers, determining the working conditions of the atomizers, the required number of atomizers, and the application angle of the atomizers in the internal mixed dust removal system. Finally, the atomized dust control system was applied on-site, achieving a total dust removal efficiency of 90.72% and a respirable dust removal efficiency of 89.75%.

mining & mineral processing,metallurgy & metallurgical engineering
Factors Determining Continuous Infusion Aerosol Delivery During Mechanical Ventilation

Michael McPeck,Sunya Ashraf,Ann D Cuccia,Gerald C Smaldone

DOI: https://doi.org/10.4187/respcare.07715

2020-09-23

Respiratory Care

Abstract:BACKGROUND:Continuous nebulization of prostacyclins and albuterol by infusion pump during mechanical ventilation evolved as a popular off-label treatment for severe hypoxemic respiratory failure and asthma. Most institutions use a vibrating mesh nebulizer. A new breath-enhanced jet nebulizer is a potential alternative. This study was designed to compare these devices to better define factors influencing continuous infusion aerosol delivery. Device function, ventilator settings, and infusion pump flow were studied in vitro.METHODS:Using a bench model of adult mechanical ventilation, radiolabeled saline was infused at 6 flows (1.5−12 mL/h) into test nebulizers; 4 examples of each were used in rotation to test device reproducibility. Four breathing patterns with duty cycles (percentage of inspiratory time) ranging from 0.13 to 0.34 were tested. The vibrating mesh nebulizer was installed on the "dry" side of the heated humidifier (37°C). The breath-enhanced jet nebulizer, installed on the "wet" side, was powered by air at 3.5 L/min and 50 psi. Infusion time was 1 h. Inhaled mass of aerosol was collected on a filter at the airway opening. Inhaled mass was expressed as the percentage of the initial syringe radioactivity delivered per hour. Radioactivity deposited in the circuit was measured with a gamma camera. Data were analyzed with multiple linear regression.RESULTS:Variation in inhaled mass was significantly explained by pump flow and duty cycle (R2 0.92) and not by nebulizer technology. Duty cycle effects were more apparent at higher pump flow. Vibrating mesh nebulizers failed to nebulize completely in 20% of the test runs. Mass balance indicated that vibrating mesh nebulizers deposited 15.3% in the humidifier versus 0.2% for breath-enhanced jet nebulizer.CONCLUSIONS:Aerosol delivery was determined by infusion pump flow and ventilator settings with comparable aerosol delivery between devices. The breath-enhanced jet nebulizer was more reliable than the vibrating mesh nebulizer; 10−12 mL/h was the maximum infusion flow for both nebulizer technologies.

respiratory system,critical care medicine
Numerical simulation of the dimensional transformation of atomization in a supersonic aerodynamic atomization dust-removing nozzle based on transonic speed compressible flow

Tian Zhang,Deji Jing,Shaocheng Ge,Jiren Wang,Xiangxi Meng,ShuaiShuai Ren

DOI: https://doi.org/10.1007/s40789-020-00314-3

2020-04-17

Abstract:Abstract To simulate the transonic atomization jet process in Laval nozzles, to test the law of droplet atomization and distribution, to find a method of supersonic atomization for dust-removing nozzles, and to improve nozzle efficiency, the finite element method has been used in this study based on the COMSOL computational fluid dynamics module. The study results showed that the process cannot be realized alone under the two-dimensional axisymmetric, three-dimensional and three-dimensional symmetric models, but it can be calculated with the transformation dimension method, which uses the parameter equations generated from the two-dimensional axisymmetric flow field data of the three-dimensional model. The visualization of this complex process, which is difficult to measure and analyze experimentally, was realized in this study. The physical process, macro phenomena and particle distribution of supersonic atomization are analyzed in combination with this simulation. The rationality of the simulation was verified by experiments. A new method for the study of the atomization process and the exploration of its mechanism in a compressible transonic speed flow field based on the Laval nozzle has been provided, and a numerical platform for the study of supersonic atomization dust removal has been established.

energy & fuels,mining & mineral processing
Effects of Vibration Characteristics on the Atomization Performance in the Medical Piezoelectric Atomization Device Induced by Intra-Hole Fluctuation

Yan, Qiufeng,Sun, Wanting,Zhang, Lei,Wang, Hongmei,Zhang, Jianhui

DOI: https://doi.org/10.1186/s10033-021-00635-7

IF: 2.964

2021-01-01

Chinese Journal of Mechanical Engineering

Abstract:Oral inhalation of aerosolized drugs has be widely applied in healing the affected body organs including lesions of the throat and lungs and it is more efficient than those conventional therapies, such as intravenous drip, intramuscular injection and external topical administration in the aspects of the dosage reduction and side effects of drugs. Nevertheless, the traditional atomization devices always exhibit many drawbacks. For example, non-uniformed atomization particle distribution, the instability of transient atomization quantity and difficulties in precise energy control would seriously restrict an extensive use of atomization inhalation therapy. In this study, the principle of intra-hole fluctuation phenomenon occurred in the hole is fully explained, and the produced volume change is also estimated. Additionally, the mathematical expression of the atomization rate of the atomizing device is well established. The mechanism of the micro-pump is further clarified, and the influence of the vibration characteristics of the atomizing film on the atomization behavior is analyzed theoretically. The curves of sweep frequency against the velocity and amplitude of the piezoelectric vibrator are obtained by the Doppler laser vibrometer, and the corresponding mode shapes of the resonance point are achieved. The influence of vibration characteristics on atomization rate, atomization height and atomization particle size are also verified by experiments, respectively. Both the experimental results and theoretical calculation are expected to provide a guidance for the design of this kind of atomization device in the future.
Investigation on High-Viscosity Chemical Waste Liquid Atomizer Based on VOF-DPM

Haoyu Ou,Lei Su,Yang Shi,Shijie Ruan

DOI: https://doi.org/10.3390/en16073109

IF: 3.2

2023-03-30

Energies

Abstract:The viscosity of adiponitrile waste liquid is as high as 1000 cp. It is challenging to spray and atomize the waste liquid normally. Based on the coaxial three-channel pneumatic atomizer, a two-stage supersonic steam atomizer is proposed in this paper, and the atomization process is simulated by Fluent software. Compared with the traditional atomization simulation method, the Volume-of-Fluid to Discrete-Phase-Model (VOF-DPM) bi-directional coupling model and Adaptive Mesh Refinement (AMR) technology can save mesh and improve the computational efficiency. The atomization processes of primary breakup and secondary breakup are entirely captured and analyzed. The results show that the Sauter Mean Diameter (SMD) is about 116–180 μm, the SMD decreases with the increase of steam inlet absolute pressure, and the atomization quality can meet the combustion requirements. This study can be used for the performance optimization of the high-viscosity liquid atomizers in the chemical and aerospace industry and shorten the time engineers spend in the simulation calculation to verify the rationality of the structure.

energy & fuels
Experimental studies on effervescent atomizers

Pei-yong MA,Xing-qi QIU,Yun-jing CUI

DOI: https://doi.org/10.3969/j.issn.1000-7466.2006.01.003

2006-01-01

Abstract:An effervescent atomizer was designed in this research, whose configuration can be changed easily. Experimental studies have been conducted on the flow-pattern, flow characteristics and velocity distribution. The results show that diameter and length of the mix-chamber, air-to-liquid mass flow rate ratios and configuration of air-injector have significant effects on the forming of bubbly flow in the mix-chamber. The main factors, which have influences on flow characteristics, are configuration and operating parameters.
Comparison of Vibrating Mesh, Jet, and Breath-Enhanced Nebulizers During Mechanical Ventilation

Sunya Ashraf,Michael McPeck,Ann D Cuccia,Gerald C Smaldone

DOI: https://doi.org/10.4187/respcare.07639

2020-07-21

Respiratory Care

Abstract:BACKGROUND:This study compared 3 nebulizer technologies for inter- and intradevice reproducibility, humidification, and fill volume sensitivity during mechanical ventilation: a breath-enhanced jet nebulizer, a vibrating mesh nebulizer, and a jet nebulizer. The breath-enhanced jet nebulizer featured a new design located on the wet side of the humidifier to reduce aerosol loss and potential humidifier contamination. The vibrating mesh nebulizer and the jet nebulizer were placed on the dry side.METHODS:Aerosol delivery was measured using multiple ventilator settings (inspiratory time = 0.45–1.01 s). Using radiolabeled saline and a gamma camera, bench studies were performed using a ventilator to test 4 breathing patterns. Four scenarios were assessed during testing: 3 mL and 6 mL fill volumes with and without heated wire humidification. Measurements included inhaled mass (as a percentage of the nebulizer charge), nebulizer residual, mass balance, and aerosol particle size distribution. Statistics were determined using Mann-Whitney and linear regression.RESULTS:The inhaled mass for the breath-enhanced jet nebulizer was 10.5–29.2% and was affected by fill volume (P = .004) but not by humidity. The inhaled mass for the vibrating mesh nebulizer was 0.9–33% and was unaffected by fill volume and humidity. The inhaled mass for the jet nebulizer was 2.5–25.9% and was affected by both fill volume (P = .009) and humidity (3 mL, P = .002). The inhaled mass for the vibrating mesh nebulizer was more variable due to random failures to achieve complete nebulization, and inhaled mass correlated closely with residual mass: IM% = –0.233(Residual%) + 24.3, r2 = 0.67, P < .001. For all devices, large particles were lost in the ventilator tubing; large particles were also lost in the humidifier for the vibrating mesh nebulizer (17% nebulizer charge), resulting in similar particle distributions (mass median aerodynamic diameter 1.33–1.95 μm) for all devices.CONCLUSIONS:Nebulization with the breath-enhanced jet nebulizer was less sensitive to humidification than the jet nebulizer. Delivery via the vibrating mesh nebulizer was not predictable, with random failure to empty (55% experimental runs). All devices delivered similar particle distributions. Wet-side aerosol delivery avoids humidifier contamination, and breath-enhanced technology can ensure better control of drug delivery.

respiratory system,critical care medicine

Simulation Analysis on Nebulizing Effects of Supersonic Atomizer Adapted to Ventilator

Numerical Comparison of the Efficiency of Mixing Ventilation and Impinging Jet Ventilation for Exhaled Particle Removal in a Model Intensive Care Unit

Three-Dimensional Simulation Of Effervescent Atomization Spray

Optimization of Vibrating Mesh Nebulizer Air Inlet Structure for Pulmonary Drug Delivery

Simulation of Effervescent Atomization and Nanoparticle Characteristics in Radio Frequency Suspension Plasma Spray

Simulation of Droplet-gas Flow in the Effervescent Atomization Spray with an Impinging Plate

Dissecting the performance of a jet nebulizer: The effect of changing design parameters and operating conditions

Effects of different mesh nebulizer sources on the dispersion of powder formulations produced with a new small-particle spray dryer

Numerical Simulation of the Nebulizer with Multiple Orifices

Study on influencing factors of patients accepting Ventavis ultrasonic atomizing inhalation

Effects of operating conditions on droplet deposition onto surface of atomization impinging spray

Numerical Simulation of Effect of Various Parameters on Atomization in an Annular Slit Atomizer

Aerosol Delivery to Simulated Spontaneously Breathing Tracheostomized Adult Model With and Without Humidification

Multi-Physics Coupled Acoustic-Mechanics Analysis and Synergetic Optimization for a Twin-Fluid Atomization Nozzle

Experimental and Numerical Simulation Studies on the Atomization Characteristics of the Internal Mixing Nozzle and Its Field Application

Factors Determining Continuous Infusion Aerosol Delivery During Mechanical Ventilation

Numerical simulation of the dimensional transformation of atomization in a supersonic aerodynamic atomization dust-removing nozzle based on transonic speed compressible flow

Effects of Vibration Characteristics on the Atomization Performance in the Medical Piezoelectric Atomization Device Induced by Intra-Hole Fluctuation

Investigation on High-Viscosity Chemical Waste Liquid Atomizer Based on VOF-DPM

Experimental studies on effervescent atomizers

Comparison of Vibrating Mesh, Jet, and Breath-Enhanced Nebulizers During Mechanical Ventilation