Abstract:Membrane biofouling represents a major challenge ever-present in the practical application of polyamide (PA) thin-film composite (TFC) reverse osmosis (RO) membranes. This work focused on grafting polyacrylamide (PAAm) onto PA-TFC via an in-situ atomic transfer radical polymerization (ATRP) method to improve the biofouling resistance of PA-TFC. The ATRP initiators, isobutyryl bromide (iPB), were introduced into PA matrix using a bifunctional small molecule, 2-bromoisobutyryl bromide (BIBB), added in organic hexane solutions to participate in interfacial polymerization through the condensation reaction with m-phenylenediamine. The successful introduction of iPB was confirmed by membrane surface characterizations, and the iPB density in PA layer was tuned by varying the BIBB concentrations in hexane solutions based on the variation in water permeance and salt rejections of iPB-loaded PA-TFC. The ATRP for the gradual growth of PAAm brush was thus in-situ achieved on the PA-TFC surface from the pre-incorporated iPB groups and the length of PAAm chains was facilely controlled via tuning ATRP polymerization time. The PAAm grafted PA-TFC exhibited a minimum decrement of water permeance and essentially retained salt rejections relative to the un-grafted ones. More importantly, the grafted membranes presented synergistically enhanced anti-adhesion and bacteriostatic performance towards either Gram-negative Escherichia coli (E. coli) or Gram-positive Bacillus subtilis (B. subtilis). Also, the grafted membranes presented a lower final flux decline ratio (FDRf) and higher final flux recovery ratio (FRRf) in relation with the un-grafted membranes in the dynamic bovine serum albumin (BSA) fouling test. Particularly, the membrane grafted with longer PAAm chains from extended grafting time showed better anti-biofouling performance: the sterilization ratio towards E. coli and B. subtilis achieved up to 98.8% and 99.0%, respectively, and FDRf of just 3.7% and FRRf of 97.6% after 3 × 8 h BSA fouling test for the membrane subjected to 2 h ATRP grafting. The PAAm grafting induced greater water wettability of membrane surface and the flexible chain structure of PAAm were proposed to account for the enhanced anti-adhesion and bacteriostasis towards bacteria, which collaboratively led to the improved biofouling resistance.

Fouling Control In A Submerged Membrane-Bioreactor By The Membrane Surface Modification

Improvement of the Antifouling Characteristics for Polypropylene Microporous Membranes by the Sequential Photoinduced Graft Polymerization of Acrylic Acid

Improved Antifouling Properties of Polyvinyl Chloride Blend Membranes by Novel Phosphate Based-Zwitterionic Polymer Additive

Photoinduced graft polymerization of acrylamide on polypropylene microporous membranes for the improvement of antifouling characteristics in a submerged membrane-bioreactor

Modification of microfiltration membranes by alkoxysilane polycondensation induced quaternary ammonium compounds grafting for biofouling mitigation

Surface Modification of Polyvinylidene Fluoride Membrane by Atom-Transfer Radical-Polymerization of Quaternary Ammonium Compound for Mitigating Biofouling

Achieving highly effective non-biofouling performance for polypropylene membranes modified by UV-induced surface graft polymerization of two oppositely charged monomers.

Preparation and Characterization of an Amphiphilic Polyamide Nanofiltration Membrane with Improved Antifouling Properties by Two-Step Surface Modification Method

Modification of poly(vinylidene fluoride)/polyethersulfone blend membrane with polyvinyl alcohol for improving antifouling ability

Enhanced Fouling-Resistance Performance of Polypropylene Hollow Fiber Membrane Fabricated by Ultrasonic-Assisted Graft Polymerization of Acrylic Acid

Surface Modification Of Microporous Polypropylene Membranes By Plasma-Induced Graft Polymerization Of Alpha-Allyl Glucoside

Acrylonitrile-Based Copolymer Membranes Containing Reactive Groups: Surface Modification By The Immobilization Of Poly(Ethylene Glycol) For Improving Antifouling Property And Biocompatibility

Antifouling Poly(Vinylidene Fluoride) Hollow Fiber Membrane With Hydrophilic Surfaces By Ultrasonic Wave-Assisted Graft Polymerization

Enhancing Antibiofouling Performance of Polysulfone (psf) Membrane by Photo-Grafting of Capsaicin Derivative and Acrylic Acid

Polypropylene Hollow Fiber Membranes With Grafted Poly(Acrylic Acid) Brushes From Surface-Initiated Atom Transfer Radical Polymerization And Their Ph-Dependent Antifouling Properties

Surface Modification Of Uhmwpe/Fabric Composite Membrane Via Self-Polymerized Polydopamine Followed By Mpeg-Nh2 Immobilization

Improving the biofouling resistance of polyamide thin-film composite membrane via grafting polyacrylamide brush on the surface by in-situ atomic transfer radical polymerization

The Effect of Grafting Monomer Charge on the Antifouling Performance of Poly(ether Ether Ketone) Hollow Fiber Membrane by Ultraviolet Irradiation Polymerization

Surface Modification of Polypropylene Microfiltration Membrane by Grafting Poly(sulfobetaine Methacrylate) and Poly(ethylene Glycol): Oxidative Stability and Antifouling Capability

Improving the antifouling property of polypropylene hollow fiber membranes by in situ ultrasonic wave-assisted polymerization of styrene and maleic anhydride

Enhancing the antifouling property of polymeric membrane via surface charge regulation