Abstract:Membrane biofouling represents a major challenge ever-present in the practical application of polyamide (PA) thin-film composite (TFC) reverse osmosis (RO) membranes. This work focused on grafting polyacrylamide (PAAm) onto PA-TFC via an in-situ atomic transfer radical polymerization (ATRP) method to improve the biofouling resistance of PA-TFC. The ATRP initiators, isobutyryl bromide (iPB), were introduced into PA matrix using a bifunctional small molecule, 2-bromoisobutyryl bromide (BIBB), added in organic hexane solutions to participate in interfacial polymerization through the condensation reaction with m-phenylenediamine. The successful introduction of iPB was confirmed by membrane surface characterizations, and the iPB density in PA layer was tuned by varying the BIBB concentrations in hexane solutions based on the variation in water permeance and salt rejections of iPB-loaded PA-TFC. The ATRP for the gradual growth of PAAm brush was thus in-situ achieved on the PA-TFC surface from the pre-incorporated iPB groups and the length of PAAm chains was facilely controlled via tuning ATRP polymerization time. The PAAm grafted PA-TFC exhibited a minimum decrement of water permeance and essentially retained salt rejections relative to the un-grafted ones. More importantly, the grafted membranes presented synergistically enhanced anti-adhesion and bacteriostatic performance towards either Gram-negative Escherichia coli (E. coli) or Gram-positive Bacillus subtilis (B. subtilis). Also, the grafted membranes presented a lower final flux decline ratio (FDRf) and higher final flux recovery ratio (FRRf) in relation with the un-grafted membranes in the dynamic bovine serum albumin (BSA) fouling test. Particularly, the membrane grafted with longer PAAm chains from extended grafting time showed better anti-biofouling performance: the sterilization ratio towards E. coli and B. subtilis achieved up to 98.8% and 99.0%, respectively, and FDRf of just 3.7% and FRRf of 97.6% after 3 × 8 h BSA fouling test for the membrane subjected to 2 h ATRP grafting. The PAAm grafting induced greater water wettability of membrane surface and the flexible chain structure of PAAm were proposed to account for the enhanced anti-adhesion and bacteriostasis towards bacteria, which collaboratively led to the improved biofouling resistance.

Photoinduced graft polymerization of acrylamide on polypropylene microporous membranes for the improvement of antifouling characteristics in a submerged membrane-bioreactor

Improvement of the Antifouling Characteristics for Polypropylene Microporous Membranes by the Sequential Photoinduced Graft Polymerization of Acrylic Acid

Fouling Control In A Submerged Membrane-Bioreactor By The Membrane Surface Modification

Improving the Hydrophilicity of Poly(vinylidene Fluoride) Porous Membranes by Electron Beam Initiated Surface Grafting of AA/SSS Binary Monomers

Surface immobilization of polymer brushes onto porous poly(vinylidene fluoride) membrane by electron beam to improve the hydrophilicity and fouling resistance

Surface Modification Of Microporous Polypropylene Membranes By Plasma-Induced Graft Polymerization Of Alpha-Allyl Glucoside

Improving the biofouling resistance of polyamide thin-film composite membrane via grafting polyacrylamide brush on the surface by in-situ atomic transfer radical polymerization

Achieving highly effective non-biofouling performance for polypropylene membranes modified by UV-induced surface graft polymerization of two oppositely charged monomers.

Free radical graft polymerization of hydroxyethyl methacrylate and acrylic acid on polyetherimide membrane surface via redox system to improve anti-fouling and oil resistance performance

Microporous polypropylene hollow fiber membrane Part I. Surface modification by the graft polymerization of acrylic acid

Preparation of hydrophilic polypropylene hollow fiber membranes by UV modification

Antifouling and Self-Cleaning Performances of the Porous Polypropylene Membrane Surface Grafted by P(NIPAAm-PEGMA)

Surface modification of polypropylene microporous membranes to improve their antifouling property in MBR: NH3 plasma treatment

Surface Modification of Poly(tetrafluoroethylene) Films Via Plasma Treatment and Graft Copolymerization of Acrylic Acid

Acrylonitrile-Based Copolymer Membranes Containing Reactive Groups: Surface Modification By The Immobilization Of Poly(Ethylene Glycol) For Improving Antifouling Property And Biocompatibility

Surface modification of polypropylene microfiltration membranes by graft polymerization of N-vinyl-2-pyrrolidone

Surface Modification of Polyethylene Membrane by Adsorption of Tween 20 to Improve Antifouling Characteristics in a Bioreactor

Improvement of Surface Properties of Poly(propylene) Hollow Fiber Microporous Membranes by Plasma‐Induced Tethering of Sugar Moieties

Surface Modification of Polypropylene Microporous Membranes with a Novel Glycopolymer

Surface Hydrophilization of Microporous Polypropylene Membrane by Grafting Zwitterionic Polymer for Anti-Biofouling

Surface Modification Of Uhmwpe/Fabric Composite Membrane Via Self-Polymerized Polydopamine Followed By Mpeg-Nh2 Immobilization