Abstract:Blowing agents are key compounds for the preparation of polymer foams. However, the use of chemical blowing agents is being curtailed to address the adverse impacts on public health and the environment issues. Moreover, physical blowing agent supercritical carbon dioxide (CO 2 ) requires harsh experimental conditions such as high temperature and pressure, resulting in high energy consumption and safety problems. In this study, CO 2 was captured through amines under atmospheric pressure to form ammonium carbamate salts, which reversibly released under heating as blowing agent. Integrated nucleating-blowing agents were fabricated by heterogeneous nucleating agent (cyclodextrin nanosponges, NS) loaded with ammonium carbamate salts. The effects of types and contents of amines on the thermal and CO 2 capture efficiency were investigated. Results revealed that only amines with strong basicity like 1,2-cyclohexanediamine (TRK) was the CO 2 capture candidate to prepare ammonium carbamate salts. The mass ratio was 1:4 for NS and TRK (NS: TRK-CO 2 (1:4)), and the release temperature of CO 2 was 137 °C. Foamed polyethylene (PE) composites were prepared by molding process with NS: TRK-CO 2 (1:4). Scanning electron microscopy (SEM) images were used to study the morphology of the nanocomposites. The optimum cell morphology was obtained with 5 wt% NS: TRK-CO 2 (1:4), the cell diameter was 116 μm, and the cell density was 7.9 × 10 4 cell/cm 3 . The best fabricated microcellular PE/NS: TRK-CO 2 (1:4) composite presented excellent mechanical, thermal and sound insulating performance. The maximum tensile strength of the PE composite was 25.48 MPa, and the maximum bending strength was 11.27 MPa. The impact strength was 5.77 KJ•m -2 , more than 1.5 times higher than pure PE. The thermal conductivity was as low as 0.076 W/m•k, the sound absorption coefficient was 0.737 at 1500 Hz, and the noise reduction coefficient was 0.459.

Compound Mechanism of the Endo-Exothermic and Exo-Endothermic +_ Balanced Blowing Agent

Morphology and blowing agent encapsulation efficiency of vinylidene chloride copolymer microspheres synthesized by suspension polymerization in the presence of a blowing agent

Decomposition characteristics of blowing agent H in EPDM compound

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Significantly Tunable Foaming Behavior of Blowing Agent for the Polyethylene Foam Resin with a Unique Designed Blowing Agent System

Effect of Chemical Blowing Agent on the PVC Cellular Coating Extrusion

Study on synergistic enhancement of modified nucleating‐blowing agent and its application in foaming polyethylene

Blowing Properties of Expandable Microspheres in LDPE

Effects of formulation and processing parameters on the morphology of extruded polypropylene-(waste ground rubber tire powder) foams

Manipulation of Chain Entanglement and Crystal Networks of Biodegradable Poly(butylene Adipate-Co-butylene Terephthalate) During Film Blowing Through the Addition of a Chain Extender: an in Situ Synchrotron Radiation X-ray Scattering Study.

Calculating diffusion coefficients from molecular dynamics simulations for modelling foam processes of polypropylene: Investigating different process conditions and blowing agents

Chain Extension of Polyamide 6 Using Multifunctional Chain Extenders and Reactive Extrusion for Melt Foaming

Effects of Chain Composition of PBAT on the Supercritical CO2 Foaming and Degradation Behavior

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene

Expansion Properties And Diffusion Of Blowing Agent For Vinylidene Chloride Copolymer Thermally Expandable Microspheres

Study on Foaming Kinetics and Preparation of Epdm Foams

Study on Extrusion Foaming of Polypropylene/Polydimethylsiloxane Blends

Effect of Mixing Poly(lactic Acid) with Glycidyl Methacrylate Grafted Poly(ethylene Octene) on Optical and Mechanical Properties of the Blown Films

Structure of PBAT/PPC blends prepared by in-situ reactive compatibilization and properties of their blowing films

Application of Carbon Dioxide Capture Technology in the Process of Polyethylene Foaming Materials

The study of the chemical crosslinked and foamed PP/LDPE