Abstract:This study examines the effect of cooling rate (specifically at 2.3, 3.4, 9.8 and 24.1 K/s as) on the microstructure and mechanical properties of an Al-5.0Mg-3.0Zn-1.0Cu (wt.%) alloy casted through a step-like iron mold. This study was performed in as-cast and T6-treated (470 degrees C x 24 h + 150 degrees C x 16 h) conditions. An examination of the as-cast microstructure shows that when the cooling rate increases from 2.3 to 24.1 K/s, the average secondary dendrite arm spacing decreases from 43.0 to 19.0 mu m, and that the average width of the T-Mg-32(AlZnCu)(49) phase also decreases from 6.7 to 4.0 mu m. The solution treatment has an impact on dissolving most of the T phases and aging treatment results in the formation of fine precipitates in matrix. The examinations of precipitates under different cooling rates show that a higher cooling rate promotes the transformation from the GP II zone to eta' phase and also keeps a higher concentration of Mg and Zn suspended in the alloy matrix. The results of tensile tests show that the strength and elongation of as-cast alloys are improved slightly by applying a higher cooling rate, and that of T6-treated alloys improved more significantly, especially for elongation (from 6.1% to 10.6%) and yield strength (from 402.5 to 441.9 MPa). The refinements of alpha-Al and Al3Fe phases are attributed to the significant increase of elongation for T6-treated alloys. Moreover, cooling rate regulates the yield strength by mainly affecting precipitation strengthening and the relative mechanisms are discussed. Overall, these results show that Al-5.0Mg-3.0Zn-1.0Cu cast alloy can exhibit a strength of 450 MPa, a high ductility of 10%, and can become one of high performance cast aluminum alloys. (C) 2019 Elsevier B.V. All rights reserved.

Effect of solidification conditions on microstructure, mechanical and wear properties of Mg–5Al–3Ca–0.12Sr magnesium alloy

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Influence of Solidification Conditions on Mechanical Properties of Mg-10gd-3y-0.5zr Magnesium Alloy

Effect of Cooling Rate on the Microstructure and Mechanical Properties of Al-5Cu-0.38Mg-0.32Mn-0.1Ag Alloy Cylinder Heads

Microstructure and Properties of Mg-5Al-1.5Ca-0.4Zn Based Alloyby Semi-Solid Isothermal Heat-Treatment-die-pressure-casting Process

Microstructure and mechanical properties of Mg–8Li–xAl–0.5Ca alloys

Effect of Cooling Rate on Microstructure and Mechanical Properties of an Al-5.0Mg-3.0Zn-1.0Cu Cast Alloy

Effect of Ca content on microstructure and strength of as-extruded Mg-1.0Al-xCa alloy

Mechanical properties and microstructural analysis of AXJ530 magnesiu alloy reinforced with alumina fibers

Microstructure and Mechanical Behavior of As‐Cast, Extruded and Nanocrystalline Mg‐9Li‐3Al‐2.5Sr Alloy

Effects of Cooling Rate on Microstructure, Mechanical and Corrosion Properties of Mg–Zn–Ca Alloy

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Microstructure and Mechanical Behavior of Mg–10Li–3Al–2.5Sr Alloy

Effect of Ca/Al Ratio on Microstructure and Mechanical Properties of Mg-Al-Ca-Mn Alloys

Study on the microstructures and mechanical properties of Mg-xCa-5Zn-3Al-0.2Mn sand-casting alloy

Effect of Al on the Microstructure and Mechanical Properties of Mg–Sn–Ca–Mn Wrought Alloy

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

Microstructure and solidification behavior of permanent-mould-cast Mg-9Li-3Al-xSr magnesium alloy

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Effect of Al contents on microstructures, tensile and creep properties of Mg–Al–Sr–Ca alloy

Effect of Al on the Microstructure and Mechanical Properties of Mg–6Zn–2Sn–0.5Mn Alloy