Abstract:In Part I [Appl. Opt.58, 6067 (2019)APOPAI003-693510.1364/AO.58.006067], we used a coupled optoelectronic model to optimize a thin-film C u I n 1-ξ G a ξ S e 2 (CIGS) solar cell with a graded-bandgap photon-absorbing layer and a periodically corrugated backreflector. The increase in efficiency due to the periodic corrugation was found to be tiny and that, too, only for very thin CIGS layers. Also, it was predicted that linear bandgap-grading enhances the efficiency of the CIGS solar cells. However, a significant improvement in solar cell efficiency was found using a nonlinearly (sinusoidally) graded-bandgap CIGS photon-absorbing layer. The optoelectronic model comprised two submodels: optical and electrical. The electrical submodel applied the hybridizable discontinuous Galerkin (HDG) scheme directly to equations for the drift and diffusion of charge carriers. As our HDG scheme sometimes fails due to negative carrier densities arising during the solution process, we devised a new, to the best of our knowledge, computational scheme using the finite-difference method, which also reduces the overall computational cost of optimization. An unfortunate normalization error in the electrical submodel in Part I came to light. This normalization error did not change the overall conclusions reported in Part I; however, some specifics did change. The new algorithm for the electrical submodel is reported here along with updated numerical results. We re-optimized the solar cells containing a CIGS photon-absorbing layer with either (i) a homogeneous bandgap, (ii) a linearly graded bandgap, or (iii) a nonlinearly graded bandgap. Considering the meager increase in efficiency with the periodic corrugation and additional complexity in the fabrication process, we opted for a flat backreflector. The new algorithm is significantly faster than the previous algorithm. Our new results confirm efficiency enhancement of 84% (resp. 63%) when the thickness of the CIGS layer is 600 nm (resp. 2200 nm), similarly to Part I. A hundredfold concentration of sunlight can increase the efficiency by an additional 27%. Finally, the currently used 110-nm-thick layer of M g F 2 performs almost as well as optimal single- and double-layer antireflection coatings.

Surface profile optimization of antireflection gratings for solar cells

Efficient Inverted Polymer Solar Cells with Directly Patterned Active Layer and Silver Back Grating

Design and analysis of one-dimensional nanostructure on amorphous silicon solar cell for surface reflectance reduction

Design for optimal one-dimensional surface profile of EVA on solar cell modules

Optoelectronic optimization of graded-bandgap thin-film AlGaAs solar cells. Part II: optimal antireflection front-surface texturing

Double grating high efficiency nanostructured silicon-based ultra-thin solar cells

Geometrical Optimization of 2D MoS2-Ag Rectangular and Triangular Grating for Enhanced Solar Cell Efficiency

Hybrid Gratings for Complementary Absorption Enhancement in Ultra-thin Film Solar Cells

Light management of solar cells by implementation of nano/microstructures

Efficiency enhancement of ultrathin CIGS solar cells by optimal bandgap grading. Part II: finite-difference algorithm and double-layer antireflection coatings

Ultra-precision trapezoidal grating mixture of photonic crystal’s effect on enhancing the optoelectronic properties of thin film GaAs solar cell

Performance Improvement of Graphene/Silicon Solar Cells via Inverted Pyramid Texturation Array

Anti-reflection effect of high refractive index polyurethane with different light trapping structures on solar cells

Surface Modification and Theoretical Investigation by Simulation for Light Trapping in Silicon Heterojunction Solar Cells

Enhancement of Light Absorption by Ultra-Thin Film Solar Cells Using Graded Gratings

Optimization-based design of surface textures for thin-film Si solar cells — Are conventional Lambertian models relevant?

Optical Optimization of Ultra-Thin Crystalline Silicon Solar Cells by a Co-Simulation Approach of FEM and GA

Optimization-based Design of Surface Textures for Thin-Film Si Solar Cells.

THE OPTICAL DESIGN OF Mo TWO-DIMENSIONAL SURFACE GRATINGS FOR HIGH-TEMPERATURE SOLAR SELECTIVE ABSORPTION SURFACE

Improvements in anti-reflection coatings for high-efficiency silicon solar cells

Quasi-hemispherical pit array textured surface for increasing the efficiency of thin-film solar cells