Abstract:As a natural polyphenolic compound, tannin was characterized by high degree of aggregation and high molecular weight which made the adhesive prepared by tannin to have low degree of cross-linking. Many studies reported that the introduction of bridging agents which copolymerized with tannin can improve the polycondensation reaction ability of tannin. Therefore, this study used dimethyl carbonate（DMC）, a kind of chemical raw material with low toxi-city and environmental-friendly performance, to carbonize tannins and then copolymerized it with methylol urea（MMU） to prepare wood adhesives in order to reduce the steric hindrance between the reactive sites of tannins and improve the bonding quality of tannin resins. In this study, the structure of the resin was analyzed by the Fourier transform infrared spectroscopy（FT-IR）; the curing behavior of the resin was tested by the differential scanning calorimetry（DSC）; and the thermal stability of the cured resin product was studied by the thermogravimetric（TG） analysis. At the same time, the physical and chemical properties of the developed resin（solid content, viscosity, and gel time） and the shear strength of the plywood were also tested. The research results showed that the carbonated tannin resin had higher solid content（between 40.0% and 43.0%） and gel time, but lower viscosity compared to the non-carbonated tannin. Through the analysis of FT-IR, it was found that tannins had undergone carbonation reaction due to the action of DMC, which is beneficial to the copolymerization reaction with MMU. However, the amount of MMU was hardly to change the structure of resins. Besides, the curing temperature of carbonated tannin copolymerization series resin showed a trend of firstly rising and then falling, especially, it was showed an increased temperature when MMU was added in the level of 60 g/125 g, which indicated that the resin system had formed a completely cross-linked network. At the same time, in the TG analysis it was also found that the carbonated tannin resin had higher thermal stability than the non-carbonated resin and the level of 60 g/125 g MMU addition was the best in the experiment which formed an effective cross-linking structure. In addition, to investigate the bonding strength of plywood, it was disco-vered that the plywood made by the carbonated tannin copolymer resin exhibited higher shear strength than the non-carbonated resin. The 60 g/125 g MMU addition still had the optimal effect on the resin. However, the carbonated tannin copolymer resin did not contribute much to the reduction of the formaldehyde emission under the same MMU addition level with more formaldehyde amount.

Preparation of Carboxymethyl Larch Tannin Surfactant and Performance Analysis

Studies on Synthesis and Antibacterial Performance of Carboxymethylated Larch Tannin

Preparation and Performance of Dimethyl-Acetoxy- (2-Carboxymethyl Ether)-Lignin Ammonium Chloride Amphoteric Surfactant

Synthesis and flocculation of larch tannin/acrylamide/ dimethyldiallylammonium chloride composite

Preparation, Characterization and Performance Evaluation of a Novel Scale Inhibiting and Dispersing Copolymer Containing Natural Tannin

Study on Preparation of Tannin-Hydroxymethylated Furfuryl Alcohol Adhesives

Preparation of tannin-urea-formaldehyde resin by carbonated tannin and its bonding properties

Preparation and Evaluation of Carboxymethylated Lignin as Dispersant for Aqueous Graphite Suspension Using Turbiscan Lab Analyzer

Preparation and Kinetics of Thermal Analysis of Inorganic–Organic Composite Modified Carboxymethyl Starch and Its Applicability as Flocculant for Oily Wastewater Treatment

Greatly Improved Adsorption of N‐methylated Modified Macroporous Cross‐linked Polyacrylamide Toward Tannin from Aqueous Solution

Preparation and Surface Properties Investigation of Lignin-Phonls Non-Ionic Surfactant

Performance of Amphoteric Larch Tannin Derivative Particles for Removal of Azo Acid Dyes

Carboxymethylation of polysaccharide isolated from Alkaline Peroxide Mechanical Pulping (APMP) waste liquor and its bioactivity

Preparation and flocculation properties of carboxymethyl cellulose-graft-polyacrylamide

Synthesis and Foaming Performance of Lauramidopropyl Betaine Derivate Surfactants

Study on the preparation of amploteric lignin-based flocculant and its flocculation and decolorizing properties

Modification of Larch Bark Tannin Extracts and Property of Their Solution

Study On The Preparation And Deinking Efficiency Of The Modified Lignin-Phenols Surfactants

Improving antifouling performance of FO membrane by surface immobilization of silver nanoparticles based on a tannic acid: diethylenetriamine precursor layer for municipal wastewater treatment

Study on Synthetic Conditions of Carboxymethylated Derivatives of Polysaccharides from Tussilago farfara L.

Extraction of Organic Compound from Carboxymethyl Cellulose Wastewater