Abstract:Magnesium-based alloys show significant promise for widespread applications owing to their lightweight nature and improved mechanical properties achieved through grain refinement via hot rolling. This investigation focuses on Mg-xAl-yCa-zMn (AXM alloys), pre-heated to temperatures of 350, 400, and 450 °C and processed via both single-pass differential speed rolling (DSR) and conventional rolling (CR). The key findings reveal the interplay between processing temperature, strain rate during single-pass rolling, and an innovative approach for incorporating varying amounts of Ca, influencing grain size, quantity of dynamic recrystallization (DRX) grains, and overall mechanical properties, including strength and ductility. A noteworthy observation is the positive correlation between an increase in the total reduction during hot rolling and a higher fraction of DRXed grains. This leads to a significant reduction in average grain size, diminishing from 60.3 ± 54.3 μm to 19.5 ± 14.2 μm at 40%, nearly a third the size of T4 grains (the initial homogenized microstructure of the AXM alloys). The resultant material strength experiences a doubling from an average of 125 ± 10.2 MPa (T4) to 260 ± 25.8 MPa (DSR rolled at 40%) for the AXM alloys with potential improvement in the ductility depending on rolling speed conditions. This study also aims to analyze the combination of rolling temperature, rolling speed, thickness reduction, speed difference and Ca content implemented across a wide range of temperatures and strain rates to provide a holistic approach to the processing parameters affecting the microstructure and mechanical properties of AXM alloys. Furthermore, this study provides a deeper understanding of DRX mechanisms, including continuous DRX (CDRX), discontinuous DRX (DDRX), and twinning induced DRX (TDRX), while each of these mechanisms plays a distinct role in the overall enhancement of formability and performance of magnesium alloys.

Numerical simulation of effect of temperature gradient on rolling of magnesium alloy sheets

Investigation on Temperature Change of Cold Magnesium Alloy Strips Rolling Process with Heated Roll

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Numerical Simulation of Warm Stamping of Magnesium Alloy Sheet Based on Thermo-mechanical Coupled Method

Effect of differential temperature on the interfacial microstructure evolution and mechanical properties of asymmetrically rolled Mg/Al composite plates

Deformation Microstructure and Characteristics of Cast-Rolling and Normal Rolling AZ31 Magnesium Alloy Sheets

Effect of Temperature on Microstructures, Texture and Mechanical Properties of Hot Rolled Pure Mg Sheets

INFLUENCE OF ROLLING TEMPERATURE ON THE {1011}-{1012} TWINNING IN ROLLED AZ31 MAGNESIUM ALLOY SHEETS

Thermo-Mechanical Coupled Simulation of Warm Stamping of AZ31 Magnesium Alloy Sheet

Effect of pack-rolling temperature on microstructure and mechanical properties of Mg-6Sn-3Al-1Zn Alloy

Coupled Analysis of Temperature and Flow During Twin-Roll Casting of Magnesium Alloy Strip

Hot Rolling of Az31 Magnesium Alloy and Its Effects on Microstructure and Mechanical Properties

Influence of temperature and strain rate on flow stress behavior of twin-roll cast, rolled and heat-treated AZ31 magnesium alloys

Weakened anisotropy of mechanical properties in rolled ZK60 magnesium alloy sheets with elevated deformation temperature

The Coupled Temperature Field Model of Difficult-to-Deform Mg Alloy Foil High-Efficiency Electro-Rolling and Experimental Study

Grain Refining of AZ31 Magnesium Alloy During Temperature-Differential Hot Rolling

Analysis of Temperature-Deformation Conditions for Rolling Aluminum Alloy Al–Mg–Sc Based on FEM Modeling

Influence of Processing Temperature and Strain Rate on the Microstructure and Mechanical Properties of Magnesium Alloys Processed by Single-Pass Differential Speed Rolling

Numerical Simulation Research on the Temperature Field and Hot Roll Crown Model of Hot Continuous Rolling Mills

Dynamic recrystallization mechanism and near-isotropic mechanical properties of WE43 magnesium alloy sheets rolled at different temperatures

Numerical Simulation of Isothermal Forging Process of MB26 Magnesium Alloy