Abstract:While the addition of WC increases the hardness and wear resistance of coatings, an excessive WC content can also induce crack initiation and propagation, increasing brittleness and leading to premature failure. Therefore, in this study, WC particles were incorporated into nickel-based coatings by plasma-arc surfacing to optimize their content and distribution, balancing their tensile properties and wear resistance. The coatings were comprehensively evaluated through microstructural analysis, hardness testing, wear resistance assessment, and tensile testing. The results show that as the mass fraction of WC increased from 45% to 65%, the increase in carbon significantly promoted the formation of M7C3, M6C, and M23C6 carbides and suppressed the formation of the γ-phase. The microstructural analysis showed that the content of massive carbides increased significantly with the increasing WC content, and the XPS analysis further confirmed that the changes in the WC and Cr7C3 phases were particularly pronounced in the high-WC coating. The 65% WC coating showed higher hardness (a 232 increase in HV1.0), a lower and more stable coefficient of friction (0.42), and better wear resistance than the 45% WC coating, with a wear rate of 3.329 × 10−6 mm3/(N·m)−1, which was 3.709 × 10−6 mm3/(N·m)−1 lower than that of the 45% WC coating. The conventional tensile test results show that the maximum stress and strain of the 45% WC coating were 71% and 36% higher than those of the 65% WC coating, respectively. In addition, the 45% WC coating exhibited better ductility and quasi-cleavage characteristics, whereas the 65% WC coating showed typical brittle cracking behavior. The results of the field tensile tests also showed that the fracture time of the 65% WC coating was 27 s shorter than that of the 45% WC coating. Overall, the 45% WC coating had a good combination of strength and toughness.

Dissolving and Precipitating Characteristics of WC and Carbides in the Ni60A+WC Graded Coating

Preparation,Microstructure and Performance of WC-Ni Reinforced Fe-based Graded Coating

Precipitation of M6C Particle in the Ni60A+WC Reinforced Fe-based Graded Coating

Microstructure and Properties of WC-Ni/Fe Grandient Coating on Q235 Steel Formed by Plasma Cladding

Effect of WC on microstructure, molten pool and properties of Ni based coatings by multi-layer laser cladding

Study on Melting–Precipitation Evolution of WC in Ni/WC-12Co Coating during Laser Cladding and Tribological Properties

Structural Evolution and Tribological Properties of WC Particles-Strengthened Nickel-Based Cladding Layers

Investigation on the Ni60-WC composite coatings deposited by extreme-high-speed laser-induction hybrid cladding technology: Forming characteristics, microstructure and wear behaviors

Effect of Powder Size and Volume Fraction of WC on the Microstructure of Laser Cladding WC-NiCrBSi Composite Coatings

Effect of WC content on microstructure and properties of high-speed laser cladding Ni-based coating

Sedimentation Suppression and Precipitation Regulation of WC-reinforced Particles in Plasma Arc Deposited Ni-based Coatings Via an Alternating Magnetic Field

Influence of WC grain size on the microstructure and wear property enhancement of 18Ni300 coatings

Influence of WC ceramic particles on structures and properties of laser cladding Ni50-WC coatings

Formation of WC/Ni hard alloy coating by laser cladding of W/C/Ni pure element powder blend

Microstructure and Properties of WC/Ni-Based Laser-Clad Coatings with Different WC Content Values

Synthesizing of WC/Ni Hard Alloy Coating by Laser Cladding with Powder Feeding and the Growth Morphology of WC Crystals

Dissolving Mechanism of the WC/W2Cp in NiCrBSi Alloy and Surface Modification for the WC/W2Cp by Carburizing

Strengthening Mechanism and Properties of Co–WC Composite Coatings Deposited by Plasma‐transferred Arc Welding

Optimizing Wear Resistance and Tensile Strength of Nickel-Based Coatings through Tungsten Carbide Reinforcement

Effect of Chromium Carbide Addition on the Microstructures and Properties in Dual Carbide Phases Reinforced Ni-Based Composite Coatings by Plasma Cladding

Fabrication and Microstructure of ZrO2/NiCrCoAlY Graded Coating by Plasma Spraying