Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

A model study of coke layer collapse in charging process in blast furnace

Central Coke Charging and Its Effect on Coke Collapse at the Throat of Blast Furnace by DEM Simulation

Numerical simulation of coke collapse and its optimization during burden charging at the top of bell-less blast furnace

VFM-based Modelling of Burden Descent under Varying Burden Charging Matrix for Blast Furnace

The Influence of Central Coke Charging Mode on the Burden Surface Shape and Distribution of a Blast Furnace

Numerical Investigation of the Limit of Coke Rate Reduction in an Ironmaking Blast Furnace (BF)

CFD-DEM Study on the Synergistic Effect of Coke Consumption and Particle Dynamics in the Blast Furnace Raceway

Study on the High-Temperature Interaction between Coke and Iron Ores with Different Layer Thicknesses

Influence of Central Coke Ratio on the Internal State of Blast Furnace

Numerical Simulation of Hot Metal Carbonization by Dead‐Man Coke in the Blast Furnace Hearth

Mathematical Model of Hearth and Bottom Erosion in Blast Furnace

Effect of the coke particle size distribution on the burden layer porosity of blast furnace

Measurement and Simulation Validation of DEM Parameters of Pellet, Sinter and Coke Particles

Influences of Scaffold and Coal Injection on Gas and Liquid Flow Distributions in Blast Furnace: Mathematical Model

Relationship and Mechanism Analysis of Soft-Melt Dropping Properties and Primary-Slag Formation Behaviors of the Mixed Burden in Increasing Lump Ore Ratio

A blast furnace coke ratio prediction model based on fuzzy cluster and grid search optimized support vector regression

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Three-dimensional transient modelling of coal and coke co-combustion in the dynamic raceway of ironmaking blast furnaces

Evolution of Coke Microstructure and Metallurgical Properties During Graphitization in a Blast Furnace

Three-Dimensional Modeling of an Ironmaking Blast Furnace with a Layered Cohesive Zone

Modeling, Stability and Stick-Slip Behaviour Analysis of Coke Pushing System