Abstract:The investigation concentrates on friction stir welded (FSW) Al–Cu–Li alloy concerning its local microstructural evolution and mechanical properties. The grain features were characterized by electron back scattered diffraction (EBSD) technology, while precipitate characterization was conducted by using transmission electron microscopy (TEM) aligned along [011] Al and [001] Al zone axes. The mechanical properties are evaluated through micro-hardness and tensile testing. It can be found that nugget zones exhibit finely equiaxed grains evolved through complete dynamic recrystallization (DRX), primarily occurring in continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX). In the thermal–mechanically affected zone (TMAZ), numerous sub-structured grains, exhibiting an elongated morphology, were created due to partial DRX, signifying the dominance of CDRX, DDRX, and geometric dynamic recrystallization (GDRX) in this region. T 1 completely dissolves in the nugget zone (NZ) leading to the formation of Guinier–Preston zones and increase of δ′, β′ and S′. Conversely, T 1 partially solubilizes in TMAZ, the lowest hardness zone (LHZ) and heat affected zone (HAZ), and the residual T 1 undergoes marked coarsening, revealing various T 1 variants. The solubilization and coarsening of T 1 are primary contributors to the degradation of hardness and strength. θ′ primarily dissolves and coarsens in NZ and TMAZ, whilst this precipitate largely coarsens in HAZ and LHZ. σ, T B , grain boundary phases (GBPs) and precipitate-free zone (PFZ) are newly generated during FSW. σ exists in the TMAZ, LHZ and HAZ, whereas T B nucleates in NZ. GBPs and PFZ mostly develop in LHZ and HAZ, which can cause strain localization during tensile deformation, potentially leading to LHZ joint fracture.

Phase Transformations in Yttrium –aluminium Oxides in Friction Stir Welded and Recrystallised PM2000 Alloys

Oxidation Mechanism of Three Fe-Al Alloys with and Without Addition of 0.1 At% Yttrium at 800 °C

High-Temperature Steam Oxidation and Surface Microstructure Evolution of Fe13Cr6Al(1–4)Mo0.15Y Alloys

New insights into the mechanism of yttrium changing high-temperature oxide growth of Fe-13Cr–6Al–2Mo–0.5Nb alloy for fuel cladding

Yttrium effect on 475 °C brittleness of Fe–13Cr–6Al–2Mo-0.5Nb-0.15Zr alloy

Plasticity improvement of Fe-13Cr-6Al-2Mo-0.5Nb alloy with yttrium addition by hindering Laves phase precipitation

Evolution of microstructure and texture in a warm-rolled yttria dispersion-strengthened tungsten plate during annealing in the temperature range between 1200 °C and 1350 °C

Microstructure Evolution and Mechanical Properties of Friction Stir Welded Al–Cu–Li Alloy

Microstructures and Ion-Irradiation Behaviour of Friction Stir Welded 12Cr-Ods Steel

Recrystallization Kinetics of Larger Yttria Particle Dispersion Tungsten Alloy Warm Rolled to 50% Thickness Reduction

Precipitate Structure, Microstructure Evolution Modeling and Characterization in an Aluminum Alloy 7050 Friction Stir Weld

Friction Stir Welding of Al-Li AA2199: Parameters, Precipitates and Post Weld Heat Treatment

The Evolution of Abnormal Grains during the Heating Stage of a Post-Weld Solution Treatment in a Friction-Stir-Welded 2519 Aluminium Alloy

Recrystallization Kinetics of 50% Hot-Rolled 2% Y2O3 Dispersed Tungsten

Microstructures and Antioxidation of W Self-Passivating Alloys: Synergistic Effect of Yttrium and Milling Time

Microstructure evolution and mechanical properties of a novel γ′ phase-strengthened Ir-W-Al-Th superalloy

The Effects of Yttrium on the Mechanical Alloying of AlW System

Precipitate stability and recrystallisation in the weld nuggets of friction stir welded Al-Mg-Si and Al-Mg-Sc alloys

Effects of yttrium additions on microstructures and mechanical properties of cast Al-Cu-Mg-Ag alloys

Effect of Cr and Y on the microstructure and mechanical properties of Fe-Cr-Al alloys during corrosion-aging in superheated steam at 500 °C

Microstructure Evolution and Grain Refinement in 2319 Aluminium Alloy Via Wire Arc Additive Manufacturing Coupled with Multi-Pass Friction Stir Processing