Abstract:Fillers have been widely used in natural rubber (NR) products. They are introduced to serve as a strategy for modifying the final properties of NR vulcanizates. Silica and calcium carbonate (CaCO3) are among the fillers of choice when the color of the products is concerned. In this case, a special focus was to compare the vulcanizing efficiency of NR filled with two different filler types, namely nano-sized silica and micrometer-sized CaCO3. This study focused on the effects of the loading level (10–50 parts per hundred parts of rubber, phr) on the final properties and structural changes of NR composites. The results indicated that increased filler loading led to higher curing torques and stiffness of the rubber composites irrespective of the type of filler used. The better filler dispersion was achieved in composites filled with CaCO3 which is responsible for less polarity of CaCO3 compared to silica. Good filler distribution enhanced filler–matrix interactions, improving swelling resistance and total crosslink density, and delaying stress relaxation. The modulus and tensile strength of both composites also improved over the content of fillers. The CaCO3-filled composites reached their maximum tensile strength at 40 phr, exceeding, by roughly 88%, the strength of an unfilled sample. Conversely, the maximum tensile strength of silica-filled NR was at 20 phr and was only slightly higher than that of its unfilled counterpart. This discrepancy was ascribed to the stronger rubber–filler interactions in cases with CaCO3 filler. Effective rubber–filler interactions improved strain-induced crystallization, increasing crystallinity during stretching and reducing the strain at which crystallization begins. In contrast, large silica aggregates with poor dispersion reduced the overall crosslink density, and degraded the thermomechanical properties, tensile properties, and strain-induced crystallization ability of the NR. The results clearly indicate that CaCO3 should be favored over silica as a filler in the production of some rubber products where high performance was not the main characteristic.

PRELIMINARY STUDY ON PROCESSING OIL-BASED CALCIUM CARBONATE MUD(OBCCM) INTO RUBBER FILLERS

Advanced montmorillonite modification by using corrosive microorganisms as an alternative filler to reinforce natural rubber

Effect of Surface Modifications of Carbon Black (CB) on the Properties of CB/polyurethane Foams

Modification of the Filler based on Kaolin and its Use in the Polymer Composites

Enhanced Mechanical Properties of Natural Rubber by Block Copolymer-Based Porous Carbon Fibers

Mechanical and Thermal Properties of Polypropylene (PP) Composites Filled with CaCO3 and Shell Waste Derived Bio-Fillers

Effects of Carbon Black on Mechanical Properties and Oil Resistance of Liquid Silicone Rubber

Application of Composite Powders Recycled from Graphite Tailings in Styrene-Butadiene Rubber

Study on mechanical properties and antifriction of calcium powder filled rubber

Preparation and performance of oleylamine modified silica‐reinforced natural rubber composites

Comparative Investigation of Nano-Sized Silica and Micrometer-Sized Calcium Carbonate on Structure and Properties of Natural Rubber Composites

Performance Study of Chlorophyll-Extracting Waste Oil Used As Rubber Operating Oil

Preparation of Calcium Carbonate from Cockle Shells as Fillers in Natural Rubber

Research Progress of Natural Rubber Wet Mixing Technology

Mechanism on surface hydrophobically modification of fibrous wollastonite and its reinforcement of natural rubber

Preparation of high-quality wollastonite/natural rubber composites by atomization sputtering rapid drying process

Experiment on MICP-solidified calcareous sand with different rubber particle contents and sizes

Study on the Abrasion of EPDM Rubblers

INFLUENCE OF SURFACE-MODIFICATION FOR CALCIUM CARBONATE ON THE INTERACTION BETWEEN THE FILLERS AND POLYDIMETHYLSILOXANE

The Mechanical and Viscoelastic Properties of SSBR Vulcanizates Filled with Organically Modified Montmorillonite and Silica

Understanding the Reinforcement and Dissipation of Natural Rubber Compounds Filled with Hybrid Filler Composed of Carbon Black and Silica