Abstract:This paper describes the use of PolyJet 3D printing to fabricate microchip electrophoresis devices with integrated microwire electrodes for amperometric detection. The fabrication process involves 3D printing of two separate pieces, a channel layer and an electrode layer. The channel layer is created by 3D printing on a pre-fabricated mold with a T-intersection. For the electrode layer, a stencil design is printed directly on the printing tray and covered with a piece of transparent glass. Microwire electrodes are adhered over the glass piece (guided by underlaying stencil) and a CAD design of the electrode layer is then printed on top of the microwire electrode. After delamination from the glass after printing, the microwire is embedded in the printed piece, with the stencil design ensuring that alignment and positioning of the electrode is reproducible for each print. After a thermal bonding step between the channel layer and electrode layer, a complete electrophoresis device with integrated microelectrodes for amperometric detection results. It is shown that this approach enables different microwire electrodes (gold or platinum) and sizes (100 or 50 μm) to be integrated in an end-channel configuration with no gap between the electrode and the separation channel. These devices were used to separate a mixture of catecholamines and the effect of separation voltage on the potential voltage applied on the working electrode was also investigated. In addition, the effect of electrode size on the number of theoretical plates and limit of detection was studied. Finally, a device that contains different channel heights and a detection electrode was 3D-printed to integrate continuous flow sampling with microchip electrophoresis and amperometric detection.

Electrokinetic control of fluid in plastified laser-printed poly(ethylene terephthalate)-toner microchips

Modification of Amorphous Poly(ethylene Terephthalate) Surface by UV Light and Plasma for Fabrication of an Electrophoresis Chip with an Integrated Gold Microelectrode

Plastified poly(ethylene terephthalate) (PET)-toner microfluidic chip by direct-printing integrated with electrochemical detection for pharmaceutical analysis.

Rapid prototyping of polymeric electrophoresis microchips with integrated electrodes for contactless conductivity detection

Thermoswitchable Electrokinetic Ion-Enrichment/Elution Based on a Poly(N-isopropylacrylamide) Hydrogel Plug in a Microchannel

Elimination of suction effect in interfacing microchip electrophoresis with inductively coupled plasma mass spectrometry using porous monolithic plugs.

Highly efficient dynamic modification of plastic microfluidic devices using proteins in microchip capillary electrophoresis

A high-performance polycarbonate electrophoresis microchip with integrated three-electrode system for end-channel amperometric detection.

Simulation of Cone-Jet and Micro-Drip Regimes and Printing of Micro-Scale Patterns on PET Substrate

Improved separation efficiency of neurotransmitters on a native printed capillary electrophoresis microchip simply by manipulating electroosmotic flow.

Thermo-swicthable electrokinetic ion-enrichment, elution and separation based on a poly (n-isopropylacrylamide) hydrogel plug prepared inside a glass microchannel

Use of 3D printing to integrate microchip electrophoresis with amperometric detection

A Full-Scale Computational Study on the Electrodynamics of a Rigid Particle in an Optically Induced Dielectrophoresis Chip

Fabrication of anti-protein-fouling poly(ethylene glycol) microfluidic chip electrophoresis by sandwich photolithography.

Microfabrication of Integrated Capillary Electrophoresis Chips and On-chip Sample Injection and Separation

Fabrication and performance of fiber electrophoresis microchips.

Stepwise Aggregation Control of PEDOT:PSS Enabled High-Conductivity, High-Resolution Printing of Polymer Electrodes for Transparent Organic Phototransistors

Low-voltage electroosmotic pumping using polyethylene terephthalate track-etched membrane

Electrophoresis Microchips with Sharp Inlet Tips, for Contactless Conductivity Detection, Fabricated by In-Situ Surface Polymerization

Simulation and Printing of Microdroplets Using Straight Electrode-Based Electrohydrodynamic Jet for Flexible Substrate

The Use of Poly(dimethylsiloxane) Surface Modification with Gold Nanoparticles for the Microchip Electrophoresis.