Abstract:It may be a potential way to realize high-efficiency and high-quality local loading forming on the double-action press. However, the deformation characteristics and forming quality of transitional region are the weak link during forming process. In this work, the material flow, deformation inhomogeneity, forming defect of transitional region, and their dependences on the local loading parameters were quantitatively investigated by FE simulation. It is found that due to the constraint clearance, the web material would undergo twice transverse flow with opposite directions successively in two loading steps. This phenomen is basically the same as that in the local loading forming on single-action press, while the extent of transverse material flow on double-action press is greatly smaller. Finally, the transitional region presents different strain distributions in various sub-regions. Region A and region C present a symmetric strain concentration area at rib root, while region B presents a slant strain concentration area at the middle rib. The forming quality on double-action press is better than that on the single-action press. Only a cavum defect at left rib is produced because of the transverse material flow. Constraint clearance plays the most important role in the deformation characteristics and forming quality during the local loading forming on double-action press. The transverse material flow and cavum defect can be suppressed by decreasing the constraint clearance, but the deformation inhomogeneity would increase to some extent at the same time. In addition, the friction factor and radius of left rib are the second significant factors. Increasing the friction factor and radius of left rib is helpful to suppress the transverse material flow and cavum defect, respectively. As far as the forming quality of transitional region is concerned, it is a better way to conduct the local loading forming on double-action press than on single-action press. The results will provide basis for the design of processing parameters in the local loading forming of Ti-alloy rib-web component on double-action press.

Forming Quality of Titanium Alloy Large-Scale Integral Components Isothermal Local Loading

A New Fe Modeling Method for Isothermal Local Loading Process of Large-Scale Complex Titanium Alloy Components Based on Deform-3d

Analysis on Process and Forming Defects of Large-Scale Complex Integral Component Isothermal Local Loading

H-shaped component isothermal local loading forming of TA15 titanium alloy

Forming Defects Control in Transitional Region During Isothermal Local Loading of Ti-alloy Rib-Web Component

Isothermal local loading technology and its application in large-scale integral component forming of Ti-alloy

Formation Mechanism, Prediction and Control of the Forming Defects in Transitional Region During Local Loading Forming of Ti-alloy Rib-Web Component

Analysis of Local Loading Forming for Titanium-Alloy T-Shaped Components Using Slab Method

Deformation behavior under die partitioning boundary during titanium alloy large-scale rib-web component forming by isothermal local loading

Effects of Parameters on Inhomogeneous Deformation and Damage in Isothermal Local Loading Forming of Ti-Alloy Component

Preform Design for Large-Scale Bulkhead of Ta15 Titanium Alloy Based on Local Loading Features

Research on marco-microcosmic deforming in isothermal local loading transition region for large-scale complex integral components of TA15 titanium alloy

Forming Limit of Local Loading Forming of Ti-alloy Large-Scale Rib-Web Components Considering Defects in the Transitional Region

Deformation Characteristics of Transitional Region During Local Loading Forming of Ti-alloy Rib-Web Component on the Double-Action Press

Optimization on the process of large titanium bulkhead isothermal closed-die forging

Micromechanical Behaviour of TA15 Alloy Cylindrical Parts Processed by Multi-Pass Flow Forming

Microstructure Control in Local Loading Forming of Large-scale Complex Titanium Alloy Component

Modeling and simulation of die forging process for large-scale titanium alloy forging

Optimizing the Local Microstructure and Mechanical Properties of Variable Section Particulate Reinforced Titanium Matrix Composites Component Based on Numerical Simulation and Isothermal Forming

Through-process Macro–micro Finite Element Modeling of Local Loading Forming of Large-Scale Complex Titanium Alloy Component for Microstructure Prediction

Quantitative Analysis of the Material Flow in Transitional Region During Isothermal Local Loading Forming of Ti-alloy Rib-Web Component