Abstract:Abstract The article is aimed at the study of structural features and phase chemical composition in 3.6 wt.% C-15 wt.% Cr-2 wt.% Mo cast iron prepared with adding 0.50 wt.% boron. The work was fulfilled using optical and electron scanning microscopy, EDS, XRD, hardness measurement, and thermodynamic modelling. It was found that due to boron effect the cast iron acquired hypereutectic structure consisting of the primary M7C3 carbides (5.3 vol. %) and the eutectics based on M7C3 carbide (rosette-shaped cells) and M3C carbide (coarse-net-shaped cells or Ledeburite-shaped cells). The total amount of carbide phases was 51.8 vol.% whereas the volume fractions of M7C3-eutectic cells and M3C-eutectic cells were 21.0 vol.% and 74.7 vol.% respectively. The matrix comprised austenite, martensite and pearlite whereas austenite volume fraction was measured as 32 vol.%. Chromium and molybdenum were unevenly partitioned in phases performing the opposite character of a distribution. The primary carbides contained about 37 wt.% Cr and 1.6 wt.% Mo with the stoichiometry of (Fe3.88Cr2.76Mo0.22Mn0.12Si0.02)C3. Substantial part of carbide precipitates (primary and eutectic both) exhibited the duplex nature presenting Cr-rich/Mo-depleted core (M7C3 carbide) and Cr-depleted/Mo-rich shell (M3C carbide). Duplex carbides were closely adjusted to austenite + M3C eutectic cells to be the starting interface for their solidification. A minor amount of micron-sized areas with 67.5 wt.% Mo and 4.6 wt.% Si were observed to be presumed as M6C carbide. The cast iron was subjected to holding at 950 °C for 2 hours with subsequent oil-quenching. This treatment caused the precipitation of fine secondary carbides followed by the martensite transformation which resulted in significant hardness increase from 672 HV (as-cast) to 1038 HV. The solidification sequence is discussed in terms of structure observation and Thermo-Calc modelling.

Solidification structure of C2.08Cr25.43Si1.19Mn0.43Fe70.87 powders fabricated by high pressure gas atomization

Microstructure evolution of grey cast iron powder by high pressure gas atomization

Microstructural Evolution of Gas Atomized Fe-25cr-3. 2c Alloy Powders

Microstructural characteristic of rapidly solidified W9 high speed steel powders

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Effect of particle size on the microstructure of rapidly solidified hypereutectic iron alloy powder

Microstructure evolution of Al 0.6 CoCrFeNi high entropy alloy powder prepared by high pressure gas atomization

Microstructure and Properties of Hypereutectic High Chromium White Cast Iron Prepared under Pressure

Investigation of microstructure evolution and mechanical properties of near-eutectic Fe2-CoNiCr C high entropy cast iron

Carbide Precipitation Behavior of High‐Alloy Steel During Solidification and Cooling Process

Study on the Microstructure Evolution of Fe‐6.5wt.%Si Powders Fabricated by High Pressure Gas Atomization

Pressure-dependent Microstructure Evolution of Fe-based Amorphous Alloy Powders Via High-Pressure Gas Atomization

Microstructure and crystallography of M 7 C 3 carbide in chromium cast iron

Solidification microstructure of super-α2 alloy prepared by gas atomization

Characterization of Microstructure and Phase Elemental Composition of 15 Wt.% Cr – 2 Wt.% Mo Cast Iron with Boron Addition

Study on Microstructure of T10 Steel Powders by High Pressure Gas Atomization

Tailoring the stability of iron carbides to enhance the mechanical performances of Fe–C–Mn–Si alloys

Mechanically Driven Alloying and Structural Evolution of Nanocrystalline Fe 60 Cu 40 Powder

The Effect of the Nucleation Ability on Solidified Microstructures of Gas-Atomized Fe–6.5 Wt.%si Alloy Powder

Sintering Properties and Microstructure of Fe-Ni-Co-based Superalloy Atomized Powder

Characterization of CrMnNi Steel Powders Obtained via Gas Atomization