Abstract:The diminutive additions of nickel (Ni) element have been fused to Sn-1.5Ag-0.5 mass% Cu (SAC155) lead-free solder alloy. The study was examined experimentally and computationally (using JMatPro software program) the microstructural features, thermal behavior, density, thermal diffusivity, and conductivity as well as tensile stress strain of the Sn-1.5Ag-0.5Cu-x mass %Ni (x = 0.00, 0.05, 0.10, 0.20, and 0.50) solder alloys (SAC155-xNi). The fusing additions of Ni have a little impact on the melting point of SAC155 alloy which increasing from 502 to . The microstructure of SAC155 solder alloy included coarse grains of β-Sn besides, large eutectic regions, and embedded IMCs of Ag 3 Sn and Cu 6 Sn 5 . The computed values of Gibbs free energy (G) during solidification of the β-Sn phase, Ag 3 Sn, and Sn 3 Sn 4 IMCs show the stability at , , and , respectively. The SAC155-xNi alloys involved finer β-Sn grains, large fibrous eutectic regions, (Cu,Ni) 6 Sn 5 and (Cu,Ni) 3 Sn 4 IMCs. The G of Cu 6 Sn 5 decreased from to when Ni content increased up to 0.25 mass %, then stable and steady at with more addition of Ni element. The formation of the (Cu, Ni) 6 Sn 5 and (Ni, Cu) 3 Sn 4 IMCs is motivated by the lowest Gibbs free energy, especially when Ni mass% is added to a sufficient level. The measured and computed values of specific heat at constant pressure ( C p ) of SAC155-xNi alloys show a good matching especially at lower temperatures and a little mismatch at high temperatures which decreases with increasing Ni content. The activation energy of atomic arrangement (Q) increased from 11.36 to with increasing Ni content in SAC155-xNi alloys. Thermal diffusivity (α) and conductivity (κ) of SAC155-xNi gradually decreased with increasing temperature in the range from 303 to 423 K and/or Ni content in alloys. The measured values of (κ) are slightly lower than the computed value at similar temperatures of the SAC155-xNi alloys. The decrease in (κ) may be assigned to scattering the electrons or reducing the phonon contributions due to the presence of various solute atoms and different IMCs. The results of stress-strain graphs reveal the enhancement of YS and UTS for all Ni-containing alloys. The improvement of the yield stress (YS) and ultimate tensile strength (UTS) of Ni-containing alloys is attributed to the uniform distribution of the IMCs, the reduction of β-Sn grain size, and the smoothed enlargement of the eutectic region.

Melting and Solidification Properties of the Nanoparticles of Sn3.0Ag0.5Cu Lead-Free Solder Alloy

The influences of reactive nanoparticles alloying on grain boundary and melting properties about Sn3.0Ag0.5Cu solder

Synthesis of Sn Nanoparticles and Their Size Effect on the Melting Point

Fabrication and Properties of Lead-Free Sn-Ag-Cu-Ga Solder Alloy

Effects of Nanoscale Cu 6 Sn 5 Particles Addition on Microstructure and Properties of SnBi Solder Alloys

Study of New Types Lead-Free Solder Alloys of Sn-Ag-Cu-Al-Ni and Sn-Zn-Bi-In-P

Properties and Microstructures of Sn-Ag-Cu-X Lead-Free Solder Joints in Electronic Packaging

Effect of Ni Content on the Microstructure Formation and Properties of Sn-0.7Cu-xNi Solder Alloys

Microstructure and morphology of the soldering interface of Sn-2.0Ag-1.5Zn low Ag content lead-free solder ball and different substrates

Microstructural Examination and Thermodynamic Analysis of Sn-1.5Ag-0.5Cu-x mass% Ni Lead-Free Solder Alloys

Synthesis and analysis of the structure of modified-Al2O3 particles used to increase the strength and electrical conductivity of lead-free solder based on Sn–Ag–Cu

The influences of Ag nanoparticles on voids growth and solderability about Sn3.0Ag0.5Cu/Cu solder joint

Effect of alloying elements on microstructural and electrical property in Sn–Cu–Bi lead-free solder alloys

Electrochemical corrosion behaviour of Zn-Sn-Cu-xNi lead-free solder alloys

Controllable fabrication of Sn–Bi alloy microspheres for improved lead-free solder

Shear and Fatigue Properties of Lead-Free Solder Joints: Modeling and Microstructure Analysis

Effect of surfactants on the chemical preparation of tin-silver-copper nanoparticles

Effect of Ag, Ni and Bi Additions on Solderability of Lead-Free Solders

Effect of Ag nanoparticles on microstructure, damping property and hardness of low melting point eutectic tin–bismuth solder

Microstructural, thermal and mechanical properties of Co added Sn–0.7Cu lead-free solder alloy

Research on Reliability of Sn-1.0ag-0.5cu Low-Ag Lead-Free Solder Alloy