Abstract:Monocrystalline silicon wafer is the most important raw material in chip manufacturing; wire sawing is the most common processing method of monocrystalline silicon wafer. The residual stress generated by cutting affects the subsequent polishing costs directly, as well as the fracture strength and mechanical integrity of the monocrystalline silicon wafer, thus affecting the service performance. In this paper, the generation mechanism of residual stress was analyzed based on diamond wire sawing technology. Then, based on Drucker-Prager (D-P) plastic constitutive model, the magnitude and distribution of residual stress of monocrystalline silicon chip under different process parameters were simulated by ABAQUS simulation software. Finally, the experiment of ultrasonic vibration–assisted diamond wire saw cutting monocrystalline silicon was conducted, and the residual stress of monocrystalline silicon chips were detected by blind hole method. During the detection, the strain values before and after drilling in three directions of monocrystalline silicon chips were measured by strain gauge rosette, and then the residual stress values were determined according to the strain values and the residual stress calculation theory. The experimental results showed that residual compressive stress remains on the surface of silicon wafer in both conventional wire sawing and ultrasonic vibration–assisted wire sawing. The residual compressive stress increases with the increase of the axial speed of wire saw, decreases with the increase of the wire saw feed speed, and fluctuates with the increase of the workpiece rotation speed. The residual compressive stress on the surface of the silicon wafer by ultrasonic vibration–assisted wire sawing is larger than that by conventional wire sawing. The simulation and experimental results have the same trend, which verifies the validity of the finite element model in this paper and provides theoretical support for the subsequent processing of single crystal silicon.

The Surface Quality of Monocrystalline Silicon Cutting Using Fixed Abrasive Diamond Endless Wire Saw.

Study on surface integrity and ductile cutting of PV polycrystalline silicon and wear mechanisms of electroplated diamond wire

Surface formation, morphology, integrity and wire marks in diamond wire slicing of mono-crystalline silicon in the photovoltaic industry

Experiment study on electroplated diamond wire saw slicing single-crystal silicon

Controllable Diamond Cutting of Structured Surfaces with Subnanometric Height Features on Silicon

Recent Advances in Precision Diamond Wire Sawing Monocrystalline Silicon

Influence of single diamond wire sawing of photovoltaic monocrystalline silicon on the feed force, surface roughness and micro-crack depth

Fractal analysis on the surface topography of Monocrystalline silicon wafers sawn by diamond wire

Experimental Study on the Influence of Wire-Saw Wear on Cutting Force and Silicon Wafer Surface

The effect of cut depth and distribution for abrasives on wafer surface morphology in diamond wire sawing of PV polycrystalline silicon

Experiment Comparative Analysis of Feed Rate with Velocity Control in Cutting Mono Crystalline Silicon Using a Diamond Wire Saw

Prediction of Subsurface Microcrack Damage Depth Based on Surface Roughness in Diamond Wire Sawing of Monocrystalline Silicon

Investigations on Brittle-Ductile Cutting Transition and Crack Formation in Diamond Cutting of Mono-Crystalline Silicon

A Study on the Lubrication and Cooling Mechanism of Nano–Silicon Carbide Cutting Fluids for Diamond-Wire Sawing

Research on the Ductile-Mode Machining of Monocrystalline Silicon Using Polycrystalline Diamond (PCD) Tools

Theoretical study on sawing force of ultrasonic vibration assisted diamond wire sawing (UAWS) based on abrasives wear

The surface residual stress of monocrystalline silicon in ultrasonic vibration–assisted diamond wire sawing

Surface damage and metal-catalyzed chemical etching investigation of multicrystalline silicon by diamond wire sawing

A Systematic Review of Modeling and Simulation for Precision Diamond Wire Sawing of Monocrystalline Silicon

Experimental study regarding the surface roughness of circular crystal wafers sliced by a multi-wire saw with reciprocating and rocking functions

Material Removal Mechanisms of Polycrystalline Silicon Carbide Ceramic Cut by a Diamond Wire Saw