Abstract:To investigate the formation mechanism and evaluate the silicide effect on the microstructure and me-chanical properties of Ti-5Al-5Mo-5Cr-3 Nb-2Zr-xSi (Ti-xSi, wt%, x = 0, 0.2, 0.4, 0.6, 0.8) alloys, they are melted via vacuum arc melting and observed by scanning electron microscope (SEM) and transmission electron microscopy (TEM). The results indicate that their microstructure comprises grain boundary alpha (alpha GB), secondary alpha (alpha s), primary alpha (alpha p), and residual beta phases when the Si content is less than 0.2 wt%. With an increase in the Si content from 0.4 to 0.8 wt%, the content of the TiSi phase precipitated in alpha GB phase increases. Moreover, its size increases from 40 nm to 0.8 mu m. The diffusion of Si atoms from their high concentration in the beta to the alpha phase of the supersaturated solid solution is hindered by the phase boundary, resulting in the precipitation of silicides. The high energy at the interface and the diffusion of Si accelerate this precipitation. The elongation and fracture toughness increase at 0-0.2 wt% Si and then decrease at 0.4-0.8 wt% Si, peaking at Ti-0.2Si (7.1% and 66.4 MPamiddotm1/2, respectively). The strength is improved owing to the Si solid solution strengthening, precipitation of Ti5Si3 and TiSi phases, and strengthening effect caused by the difference in crystal plane spacing between the TiSi and the alpha GB phases. A higher silicide content leads to a gradual transformation from an intergranular ductile fracture to intergranular brittle fracture.(c) 2022 Elsevier B.V. All rights reserved.

Microstructure and tribological behavior of Ti-Si-Al alloys

Microstructural Characteristics And Elevated Temperature Wear Of Ti-11si-16al Alloy

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effect of Ti on the Microstructure and Wear Behavior of a Selective Laser Melted Al-Cu-Mg-Si Alloy

Microstructure and wear resistance of laser melted Ti5Si3 / NiTi intermetallic alloys

The effect of titanium addition on the microstructure, mechanical and tribological properties of Ni3Si alloys prepared by powder metallurgy method

Microstructure Evolution and Its Effect on Mechanical Properties of Cast Ti48Al6NbxSi Alloys

Effects of Al substitution with Si and Sn on tribological performance of Ti3AlC2

Microstructure and wear resistance of laser melted Ti5Si3-TiCo-Ti2Co multiphase intermetallic alloys

Effects of Submicron-Sized TiC Particles on the Microstructure Modification and Mechanical Properties of Al-Si-Mg Alloy

Investigation of high temperature tribological performance of TiZrV0.5Nb0.5 refractory high-entropy alloy optimized by Si microalloying

Microstructure Evolution in TiAl Alloyed with Si

Effect of Si on Phase Equilibria, Mechanical Properties and Tribological Behaviour of Al-Cu Alloy

Formation Mechanism and Effect on the Mechanical Properties of TiSi Phase for Ti-5Al-5Mo-5Cr-3Nb-2Zr Alloyed by Silicon

Alloying Design of Titanium Aluminum Intermetallics and Research Progress

Influence of heat treatment on microstructure and friction and wear properties of multicomponent Al-7·5Si-4Cu alloy

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

Tribological performance of Ti3SiC2 enhanced Ni3Al matrix composites

Solidification Behavior and Mechanical Properties of Al-Si-Mg Alloy with Ti Addition

Microstructure and mechanical properties of Cu-12 Al-6 Ni with Ti addition prepared by powder metallurgy

Formation Mechanism of Tisi Phase and Silicide Kinds on Microstructure and Mechanical Properties for Ti-5al-5mo-5cr-3nb-2zr Alloyed by Silicon