Studies on the performance of modulating thickness linear periodic magnets

Xu Qing,Xu Jianming

DOI: https://doi.org/10.1016/0168-9002(87)90855-2

1987-01-01

Abstract:The performance of modulating thickness (MT) linear periodic magnets [1] in the 2-dimensional real case is discussed in this paper. Methods for reducing the undesirable higher harmonics in the magnetic field are also analysed.

What problem does this paper attempt to address?

Modulating Thickness Multipole Permanent-Magnets

Jm Xu,Q Xu

DOI: https://doi.org/10.1016/0168-9002(88)90799-1

1988-01-01

Abstract:The magnetic field distributions of modulating thickness permanent magnets [1,2] are discussed in this paper. The field distributions are calculated by using the program POISCR and the actual demagnetization curve of the REC permanent magnet material. The results show that the performance of the MT type magnets is about the same as or even better than that of the modulating magnetization direction type (MMD) [3] and that the MT type magnet with soft iron shield requires less REC material than MMD type magnets.
Effect of Magnet Thickness on Electromagnetic Performance of High Speed Permanent Magnet Machines

Jie Ma,Lijian Wu,Z. Q. Zhu

DOI: https://doi.org/10.1109/iemdc.2017.8002206

2017-01-01

Abstract:In this paper, the influence of magnet thickness on the electromagnetic performance of high speed machines is comprehensively investigated. The investigation is carried out based on a conventional 3-slot/2-pole high speed machine with diametric magnetization. Both the finite element method (FEM) and analytical models are used. The rated output torque is fixed when the magnet thickness varies. It is found that the relative thick magnet can affect the electromagnetic performance, particularly significantly reduce the on-load magnet eddy current loss as well as on-load unbalanced magnetic force (UMF). In addition, the other performance such as demagnetization, back EMF, cogging torque and torque ripple are investigated as well.
Magnet circuit design and optimization of giant magnetostrictive transducer

Ming-fan LI,Zhan-qin XIANG,Fu-zai LV

DOI: https://doi.org/10.3785/j.issn.1008-973X.2006.02.003

2006-01-01

Abstract:To optimize the electromagnetic performance of giant magnetostrictive transducer, the effects of coil's geometry and magnetic circuit components on the transducer's magnetic field characteristics and displacement output were studied, and the magnetic circuit's loss and the gap's magnetic permeability were also analyzed. The appropriate coil structure parameters were presented, and an optimized design scheme was proposed in which pure iron with high magnetic permeability was attached to both ends of the giant magnetostrictive material (GMM) to reduce loss. Both finite element simulation and experimental analysis were conducted to study the effects of different magnet circuit design schemes on the transducer's performance. The results indicate that attaching pure iron to both ends of the GMM can enhance the working magnetic field, reduce the magnetic flux leakage, and increase the displacement output with reduced current in coil, thus improve the thermal condition of the transducer.
Design Optimization and Performance Investigation of Linear Doubly Salient Slot Permanent Magnet Machines

Yiming Shen,Zhiqiang Zeng,Qinfen Lu,Lijian Wu

DOI: https://doi.org/10.1109/tia.2018.2885329

IF: 4.079

2018-01-01

IEEE Transactions on Industry Applications

Abstract:The novel doubly salient slot permanent magnet linear machines (DSSPMLMs) are proposed in this paper. First, the topology and geometric parameters of the DSSPMLMs with 12 slots are introduced, and the corresponding basic operating principle is investigated. Then, feasible slot/pole combinations and winding configurations are further analyzed. To the DSSPMLMs with 12 slots, all structures with 10/11/13/14 poles and double layer (DL)/single layer (SL) winding are optimized. Finally, the electromagnetic performance including open-circuit and static force-current characteristics are comparatively studied using 2-D finite-element analysis (FEA). The results show that the optimal slot/pole combination is 12-slots/13-poles (12s/13p) and the DL winding exhibits lower force ripple while relatively lower thrust force capability than SL winding at low electrical loadings.
Studies of the Performance of MMD- and MW-type Permanent Multipole Magnets

JM XU,Q XU,ZS YIN

DOI: https://doi.org/10.1016/s0168-9002(98)90003-1

1988-01-01

Abstract:In this paper, the performance of a modulating magnetization direction (MMD) type [1] and the newly developed modulating width (MW) type [2–4] permanent multipole magnets are studied.
STUDIES OF THE FIELD DISTRIBUTION OF THE MODULATING WIDTH MULTIPOLE PERMANENT MAGNETS

Xu J

1987-01-01

Abstract:In this paper,the magnetic field distribution of the modulating width multipole perma-nent magnets is analyzed.Only radially magnetized permanent magnet segments are used andthe required magnetic field is formed by modulating the widths of the segments in this project.In 2-dimensional ideal case pure 2N-pole magnetic field can be formed.The spatial expres-sions of the scalar potential for the ideal and real 2-dimensional cases are given.And the me-thods for reducing the undesirable higher harmonics of the magnetic field in the real case arealso discussed.
A New Type of Linear Periodic Magnets

Q XU,MS LIU,JM XU

DOI: https://doi.org/10.1016/0168-9002(86)91165-4

1986-01-01

Abstract:In this paper, a new project of linear periodic magnets — undulator and wiggler — is described. In this project, the magnet is composed of permanent magnet segments whose magnetization directions are all perpendicular to the symmetrical plane of the magnet gap. By modulating the thicknesses of the segments, the required periodic magnetic field is formed. In the ideal 2-dimensional case, the field distribution is a purely sinusoidal curve. A soft iron shield can be used to strengthen the magnetic field. In some cases, the strengthening factor is more than 2. The spatial expression of the magnet field and the image effect of the soft iron shield in the 2-dimensional ideal case are given.
Analytical Modeling of Surface-Mounted PM Machines Accounting for Magnet Shaping and Varied Magnet Property Distribution

Lijian Wu,Zi-Qiang Zhu

DOI: https://doi.org/10.1109/tmag.2014.2304272

IF: 1.848

2014-01-01

IEEE Transactions on Magnetics

Abstract:This paper develops an analytical model for predicting the magnetic field, back-electromotive force (EMF), and electromagnetic torque of surface-mounted permanent magnet machines accounting for magnet geometrical shaping and varied magnet property distribution. The magnets on the rotor are represented by the remanence, thickness, and magnetization direction functions. They are finitely segmented into magnet pieces of simple regular shape and uniform magnet property. The magnetic field of the machine is obtained by the superposition of the magnetic field due to each segment. The back-EMF and electromagnetic torque are also calculated. Using the developed model, the technique of mixed magnet material is investigated on a four-pole/six-slot machine. The analytical predictions are verified by both finite element and experimental results.
DISCUSSIONS OF THE PERFORMANCE OF TWO TYPES OF PERMANENT MULTIPOLE MAGNETS

Jie Xu

IF: 1.279

1987-01-01

Nuclear Instruments and Methods in Physics Research Section B Beam Interactions with Materials and Atoms

Abstract:The field distributions of MMD type and MW type multipole permanentmagnets are calculated by means of programme POISCR and the results aresummarized and discussed in this paper. The results show that, considering thenonlinearity of the real demagnetization curve of permanent magnet material, thefield distributions of both types of permanent magnets with the same aperatureare about the same but the field strength of MW type magnet with soft ironshield is higher than that of MMD type magnet.
Analytical Model of Electromagnetic Performance for Permanent-Magnet Vernier Machines Using Nonlinear Exact Conformal Model

Zhaokai Li,Xiaoyan Huang,Ang Liu,Zixuan Liu,Lijian Wu,Tingna Shi

DOI: https://doi.org/10.1109/tte.2021.3124369

IF: 6.519

2022-01-01

IEEE Transactions on Transportation Electrification

Abstract:This article investigates the air-gap field distribution of the permanent-magnet Vernier machine (PMVM) using a nonlinear exact conformal model (NECM) to account for slotting effect, flux modulation effect, and iron nonlinearity. The exact conformal model (ECM) based on the region of one-slot and one-flux-modulation-pole (OSECM) are introduced to show the effectiveness of the linear analytical model for PMVM. It can keep high calculation accuracy and significantly reduce the computational burden. Then, the NECM is developed from OSECM by introducing the equivalent saturation current into the air region and coil region. The lumped parameter magnetic circuit model (LPMCM) model is used to obtain the magnetic potential of the iron region and therefore calculate the equivalent saturation current. The NECM which combines LPMCM and OSECM can essentially improve the accuracy of the linear analytical model. The harmonic analysis of the air-gap field is performed to theoretically explain the component of electromagnetic torque. Both finite element model (FEM) simulation and test results are presented to validate the NECM.
Effect of permanent magnet's structure on static behavior of a superconducting thrust bearing

Zhu Changsheng,Ji Dezhi

DOI: https://doi.org/10.3969/j.issn.1001-7100.2006.04.001

2006-01-01

Abstract:Based on commercial finite element software and assumption of a total Meissner effect,the analysis method for static behavior of a high temperature superconducting thrust bearing(HTSCTB) consisted of a bulk high temperature superconductor and a permanent magnet was presented.The effect of permanent magnet's structures on the static behavior of the superconducting thrust bearing was studied.It is shown that the magnet pole arrangement and the structure of the permanent magnets have a great effect on the levitation force of the high temperature superconducting thrust bearing.The levitation force of the high temperature thrust superconducting bearing can be increased by properly arranging the magnet poles and choosing the structure of the permanent magnets.
Investigation of Novel Axially Magnetized Vernier Permanent-Magnet Machine in Cascade Structure

Bowen Xu,Jien Ma,Lijian Wu,Xiaoyan Huang,Youtong Fang

DOI: https://doi.org/10.23919/icems50442.2020.9291137

2020-01-01

Abstract:In this paper the cascade structure of axially magnetized Vernier permanent-magnet machine is proposed and discussed. The 2-D equivalent model is applied to simplify the optimization process. It is found that in cascade topology, the effect of pole ratio on output torque has different regularity when the end turn length is considered. The torque density of proposed structure can achieve 7.3kNm/m3 when the end turn length is considered.
Comparison of Conformal Mapping Models in Permanent-Magnet Vernier Machines

Li Zhaokai,Huang Xiaoyan,Chen Zhuo,Liu Ang,Yu Yelong,Liu Zixuan,Ma Ye

DOI: https://doi.org/10.1007/978-981-19-3171-0_4

2022-01-01

Abstract:This paper analyzes the magnetic field for permanent-magnet vernier machine (PMVM) based on the conformal transformation models considering both flux modulation effect and slotting effect. Three analytical models including exact conformal model (ECM), complex permeance model (CPM), and relative permeance model (RPM) are proposed and compared to show the effectiveness of different conformal models for PMVM. Finite-element simulation and test results are presented to validate the ECM.
Research on the Effect of Thickness of Permanent Magnet to the PMSM Based on Variable Magnetic Reluctance Field Adjustment

Li Chunyan,Li Chunhong,Kou Baoquan,Cheng Shukang

2010-01-01

Abstract:A permanent magnet synchronous motor with variable magnetic reluctance field adjustment (VMRPMSM) was presented. The structure is introduced and flux weakening principle was formulated. We analyze the effect of the thickness of permanent magnet to electromagnetic force on the movable permanent magnet, parameters and flux weakening performance. The analysis is corresponding to the test result which verifies the availability of the flux weakening method for VMRPMSM.
Investigation of Vibration Behaviors of Dual Permanent Magnet Vernier Machine Considering Field and Force Modulation Effects

Shengdao Zhu,Wenxiang Zhao,Yiming Shen,Xuhui Zhu,You Zhou,Christopher H. T. Lee

DOI: https://doi.org/10.1109/tte.2024.3428868

IF: 6.519

2024-01-01

IEEE Transactions on Transportation Electrification

Abstract:This article systematically investigates the field and force modulation effects on magnetic field, radial force, and electromagnetic vibration behaviors of a dual permanent magnet vernier machine (DPMVM). Firstly, the topology and working principle of the DPMVM are analyzed by artfully decoupling it into a permanent magnet vernier machine and a permanent magnet flux reverse machine. Subsequently, the magnetic field modulation effect of DPMVM with a doubly salient pole structure is investigated. The spatial order, speed, and frequency of the abundant magnetic field harmonics affected by rotor modulation and stator modulation are summarized. Afterward, the extraordinary behaviors of radial force harmonics and electromagnetic vibration of the DPMVM are studied, in which the magnetic field and force modulation effects are considered. The result shows that the combined effect of field modulation and force modulation is the trigger for the severe vibration of DPMVM. Finally, a prototype of DPMVM is fabricated, and several experiments are conducted to validate the theoretical analysis.
Magnetic Damping Analysis of Magnetoelastic Coupling Interactions for Cantilever Conductive Thin Plate

ZHANG jian-ping,DAI Yong-xia,YAN Zhi-jiang,JI Dong-mei,WANG Hao

DOI: https://doi.org/10.13229/j.cnki.jdxbgxb2011.02.005

2011-01-01

Abstract:For the cantilever conductive thin plate under external magnetic field,a theoretical model was established to describe the vibration problem of geometric nonlinearity under the mechanics-electricity-magnetism coupling interactions.This model is based on the basic laws and equations of electromagnetics and mechanics of conductive media.Furthermore,the method to determine the effective damping factor was given,and the influences of in-plane constant magnetic field on eddy,deformation and magnetic damping were quantitatively simulated.Numerical results demonstrate that the effects of geometric nonlinearity and the coupling induced magnetic damping become stronger as the in-plane constant magnetic field increases.The effective damping factor decays with the period or the time,but increases with the in-plane constant magnetic field.This study provides scientific basis for the vibration control of conductive structures in magnetic field environment.
Optimal Design of Transducers Based on the Halbach Arrays Permanent Magnet Structure

Cheng He,Ce Li,Yishun Yan,Ran Wei,Shujuan Wang

DOI: https://doi.org/10.1080/10589759.2023.2241607

2024-01-01

Nondestructive Testing And Evaluation

Abstract:For enhancing the static magnetic field and reducing the size of torsional guided wave magnetostrictive patch transducer (MPT) with permanent magnets, a MPT with Halbach arrays is proposed. The structural parameters design of the MPT can be guided by finite element simulation. It is found that increasing the central angle of the radially magnetised magnets can increase the strength of the static magnetic field, and it can be adjusted through designing the radial size and lift-off distance of the magnets. The Halbach magnet arrays composed of circumferentially magnetised magnets with a circumferential size of 6 mm and radially magnetised magnets with a circumferential size of 4 mm are selected to experimentally compare with the alternating magnetised magnet arrays composed of magnets with a circumferential size of 10 mm. The results show that the static magnetic field strength can be increased by 54.7% using Halbach magnet arrays. The proposed MPT composed of the Halbach magnet arrays and a linear solenoid array can excite and receive T(0,1) guided wave. Compared with the alternating magnetised magnet array MPT, the guided wave signal amplitude is increased by about 70% generated and received by the MPT with the Halbach magnet arrays.
Influence of the Permanent Magnet Magnetization Length on the Performance of a Tubular Transverse Flux Permanent Magnet Linear Machine Used for Electromagnetic Launch

Jibin Zou,Qian Wang,Yongxiang Xu

DOI: https://doi.org/10.1109/tps.2010.2045661

IF: 1.368

2010-01-01

IEEE Transactions on Plasma Science

Abstract:This paper investigates the underlying influence of permanent magnet (PM) magnetization length on the performance of a tubular transverse flux PM linear machine working as the propeller of an electromagnetic launcher, including its main flux linkage, cogging force, and thrust force. The theoretical analysis is brought forward and verified with 3-D numerical computations. It is shown that the cogging force increases with the increase of the PM magnetization length, whereas the main flux linkage and thrust force do not follow this rule, which is quite different from that in conventional PM machines.
Optimal Design of Magnetically Levitated Permanent-Magnet Planar Motors Using Thd2d Method

Xinhua Zhang,Hao Luo,Zebin Yang,Xiaodong Sun,Jinchun Hu

DOI: https://doi.org/10.2528/pierm15020304

2015-01-01

Progress In Electromagnetics Research M

Abstract:In order to reduce the higher harmonic component of the magnetic field in magnetically levitated permanent-magnet planar motors (PMPMs), a sinusoidal index for 2-dimensional (2D) wave is proposed and verified by calculating the average total harmonic distortion (THD) of the discrete waveform. Based on this, a novel optimal design method using THD for 2-dimensional wave (THD2D) and fundamental amplitude is proposed for PMPMs. The finite element analysis and experimental results show that the higher harmonic component of magnetic field is reduced with average fundamental amplitude invariant, and the back-EMF is better. So the optimal design method can improve the electromagnetic performance of magnetically levitated PMPMs.
Analysis, Design and Experiment of Continuous Isolation Structure with Local Quasi-Zero-Stiffness Property by Magnetic Interaction

Xiuting Sun,Feng Wang,Jian Xu

DOI: https://doi.org/10.1016/j.ijnonlinmec.2019.07.008

IF: 3.336

2019-01-01

International Journal of Non-Linear Mechanics

Abstract:In this study, magnetic interaction is applied to a continuous structure as local negative-stiffness components to improve the vibration isolation performances and to extend the vibration isolation band. According to the theory of electromagnetic fields, the mechanical model of interaction force is established. This model is used to discover that the magnetic interaction can induce the negative stiffness property locally using appropriate structural parameters. Because different structural parameters of the magnets can increase the negative stiffness strength with different effects, the parameters of the continuous beam and magnets are adjusted for the design of accurate zero stiffness property locally. Then, the relationship between structural parameters and effective isolation bandwidth is established by deriving the solution of steady state around zero equilibrium. As the nonlinearity and zero-stiffness property only occur locally around zero equilibrium and the system displays the positive-stiffness property for large vibration amplitudes, the effective isolation band is significantly extended, and the amplitude–frequency curve is similar to the linear system at resonance. The relevant experiments demonstrate the remarkable tuning characteristic of structural parameters of magnets on the isolation features, which realize the improvement of isolation/protection effectiveness for time-lasting excitation at a low frequency. This study not only demonstrates the advantages of nonlinearity induced by local magnetic interaction on the improvement of isolation performances but also realizes a continuous structure with local quasi-zero stiffness applied in fields of low-frequency engineering structures.

Studies on the performance of modulating thickness linear periodic magnets

Modulating Thickness Multipole Permanent-Magnets

Effect of Magnet Thickness on Electromagnetic Performance of High Speed Permanent Magnet Machines

Magnet circuit design and optimization of giant magnetostrictive transducer

Design Optimization and Performance Investigation of Linear Doubly Salient Slot Permanent Magnet Machines

Studies of the Performance of MMD- and MW-type Permanent Multipole Magnets

STUDIES OF THE FIELD DISTRIBUTION OF THE MODULATING WIDTH MULTIPOLE PERMANENT MAGNETS

A New Type of Linear Periodic Magnets

Analytical Modeling of Surface-Mounted PM Machines Accounting for Magnet Shaping and Varied Magnet Property Distribution

DISCUSSIONS OF THE PERFORMANCE OF TWO TYPES OF PERMANENT MULTIPOLE MAGNETS

Analytical Model of Electromagnetic Performance for Permanent-Magnet Vernier Machines Using Nonlinear Exact Conformal Model

Effect of permanent magnet's structure on static behavior of a superconducting thrust bearing

Investigation of Novel Axially Magnetized Vernier Permanent-Magnet Machine in Cascade Structure

Comparison of Conformal Mapping Models in Permanent-Magnet Vernier Machines

Research on the Effect of Thickness of Permanent Magnet to the PMSM Based on Variable Magnetic Reluctance Field Adjustment

Investigation of Vibration Behaviors of Dual Permanent Magnet Vernier Machine Considering Field and Force Modulation Effects

Magnetic Damping Analysis of Magnetoelastic Coupling Interactions for Cantilever Conductive Thin Plate

Optimal Design of Transducers Based on the Halbach Arrays Permanent Magnet Structure

Influence of the Permanent Magnet Magnetization Length on the Performance of a Tubular Transverse Flux Permanent Magnet Linear Machine Used for Electromagnetic Launch

Optimal Design of Magnetically Levitated Permanent-Magnet Planar Motors Using Thd2d Method

Analysis, Design and Experiment of Continuous Isolation Structure with Local Quasi-Zero-Stiffness Property by Magnetic Interaction