Abstract:Gravitational melt-stir casting produced hybrid nano-reinforcements (β-SiCp) and micro-reinforcements (Bi and Sb) of AZ91 composites. SiCp-diffused discontinuous β-Mg17Al12 precipitation with a vital factor of SiC was exhibited at the grain boundary region, formulated Mg3Si throughout the composite and changed the present Mg0.97Zn0.03 phases. The creation of Mg2Si (cubic) and SiC (rhombohedral axes) enhanced the microhardness by 18.60% in a 0.5 wt.% SiCp/AZ91 matrix. The microhardness of 1 wt.% SiCp/AZ91 was slightly reduced after Mg0.97Zn0.03 (hexagonal) reduction. The best ultimate tensile value obtained was about 169.33 MPa (increased by 40.10%) in a 0.5 wt.% SiCp/AZ91 matrix. Microelements Bi and Sb developed Mg3Bi2, Mg3Sb2 and monoclinic C60 phases. The best peak yield strength of 82.75 MPa (increased by 19.85%) was obtained with the addition of 0.5 wt.% SiCp/1 wt.% Bi/0.4 wt.% Sb. The mismatch of the coefficient of thermal expansion of segregated particles and the AZ91 matrix, the shear transfer effect and the Orowan effect, combined with the quantitative value of phase existence, improved the compressive strengths of the composites with 0.5 wt.% β-SiCp, 1 wt.% β-SiCp and 0.5 wt.% SiCp/1 wt.% Bi/0.4 wt.% Sb by 2.68%, 6.23% and 8.38%, respectively. Notably, the Charpy impact strengths of 0.5 wt.% and 1 wt.% β-SiCp-added AZ91 composites were enhanced by 236% (2.89 J) and 192% (2.35 J), respectively. The addition of Bi and Sb with SiCp resulted in the formation of a massive phase of brittle Al6Mn. Al–Mn-based phases (developed huge voids and cavities) remarkably reduced impact values by 80% (0.98 J). The discussion covers the quantitative analyses of X-ray diffraction, optical microscopy and scanning electron microscopy results and fracture surfaces.

Effects of Bismuth and Antimony Additions on the Microstructure and Mechanical Properties of AZ91 Magnesium Alloy

Microstructure and mechanical properties of Mg–Al based alloy with calcium and rare earth additions

Effect of Si, Ca and Sr on the Creep-Resistance of AZ91D Alloy

Effect of Bi Addition on the Heat Resistance of As-Extruded AZ31 Magnesium Alloy

Effect of Si, Sr Additions on Microstructure and Mechanical Properties of AZ91 Alloy

Effects of Y, Gd on Microstructure and Mechanical Properties of AZ61 Magnesium Alloy

The mechanism of the influence of Bi(or Sb) and rare earth on high temperature performance of AZ91 magnesium alloy

Effect of Al3Ti3B Master Alloy on Microstructure and Mechanical Properties of AZ91D Magnesium Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

The effect of Y and Nd additions on the microstructure and creep behavior of AZ80

Effects of rare earth elements on the microstructure and properties of magnesium alloy AZ91D

Effect of Al-Nb-Ti-B addition on microstructures, tensile mechanical and damping properties of AZ91 alloy

Influence of heat treatment and pre-straining on dynamic precipitation and creep behavior of AZ91-0.5Y magnesium alloys

Effect of Aging Temperature on Microstructure and Mechanical Properties of AZ81-4%Gd Magnesium Alloy

The Effect of Gd and Zn Additions on Microstructures and Mechanical Properties of Mg-4sm-3nd-Zr Alloy

Effect of Pr addition on microstrcture and mechanical properties of AZ61 magnesium alloy

Microstructure Evaluation, Quantitative Phase Analysis, Strengthening Mechanism and Influence of Hybrid Reinforcements (β-SiCp, Bi and Sb) on the Collective Mechanical Properties of the AZ91 Magnesium Matrix

Opposite effects of Zn addition on the creep resistance at low and high temperatures for as-cast Mg-15Gd alloy

Effect of antimony additions on the microstructure and performance of Zn–Mg–Al alloy coatings