Abstract:It is suggested that fatigue failure mechanisms in the face-centered cubic metals are greatly affected by stacking fault energy. It was from this viewpoint that the fatigue crack initiation and stage I type crack propagation in 18-8 austenitic steel which had the lowest stacking fault energy among the face-centered cubic metals on the market, were discussed by the X-ray microbeam diffraction technique and the replica electron microscopic method.The fatigue slip line at room temperature tests has fine and straight configurations which are characteristic of low stacking fault energy materials, while the wavy and coarse slip line is typical of fatigue tests at 200°C where screw dislocation is more easily prone to cross slip. In both of these cases very complicated deformation configurations are caused by double slip and cross slip near the grain boundaries, and frequent extrusion and intrusion are observed in these areas. Fatigue crack nucleation might be caused by stress concentration at the notch and peak topography. The stage I type fatigue crack propagates immediately after the initiation, mainly along and frequently across the intense slip lines. Its growth in the area neighbouring the grain boundary runs in the direction that depends on both the crystal orientations of the grain containing the crack and the grains adjacent to it.Total misorientation and micro lattice strain measured by X-ray micro-beam diffraction technique increase abruptly at early fatigue stressing, then equilibrium values are attained and finally increase rapidly. These three periods during the fatigue deformation might be corresponding to those of the fine slip line initiation, the intensification of each slip line without new slip line formation and of final initiation of micro crack, respectively. Furthermore it will be noticed that the equilibrium value of total misorientation of 18-8 austenitic steel during the fatigue process is about one-tenth of that of carbon steel.The area of substructural zone near the fatigue crack of 18-8 austenitic steel is smaller than that of aluminum of high stacking fault energy and body-centered cubic iron. Therefore, the formations of subgrain and martensite could not be detected by X-ray micro-beam diffraction technique when irradiated by Cr-Kα of 200μφ beam size. In order to clarify these points the detailed observation at the fatigue crack tip must be made by using transmission electron microscopy. These results will be reported elsewhere.

Microcrack Initiation In Low-Cycle Fatigue Of An Austenitic Stainless Steel

Influence of the Crystalline Orientations on Microcrack Initiation in Low-Cycle Fatigue

The low-cycle fatigue, deformation and final fracture behaviour of an austenitic stainless steel

Variation In Mechanical Properties, Microstructures And Fracture Behavior Of 304 Stainless Steel During Low-Cycle Fatigue

Investigation of Cyclic Deformation Behavior in the Surface Layer of 18cr–8ni Austenitic Stainless Steel Based on Vickers Microhardness Measurement

Effects of low-cycle fatigue on static mechanical properties, microstructures and fracture behavior of 304 stainless steel

Microscopic Observations of Fatigue Crack Initiation Process in 18-8 Austenitic Steel

In Situ Observation of Interfacial Fatigue Crack Growth in Diffusion Bonded Joints of Austenitic Stainless Steel

High cycle thermal fatigue of two austenitic stainless steels

Microscopic Analysis by EBSD Method on Fatigue Crack Propagation Behaviour in Ultrafine-Grained Copper

Application of the EBSD technique to describe the initiation and growth behaviour of microstructurally short fatigue cracks in a duplex steel

Effect of microstructure on small fatigue crack initiation and early propagation behavior in super austenitic stainless steel 654SMO

Effects of microstructure on crack initiation in super martensitic stainless steel under very‐high‐cycle fatigue at elevated temperature

Bending Fatigue Behavior of 316L Stainless Steel up to Very High Cycle Fatigue Regime

Effects of local microstructure on crack initiation in super martensitic stainless steel under very-high-cycle fatigue

Crack Initiation Mechanisms for Low Cycle Fatigue of Type 316ti Stainless Steel in High Temperature Water

Fatigue Life and Mechanistic Modeling of Interior Micro-Defect Induced Cracking in High Cycle and Very High Cycle Regimes

Computational Modelling of Crack Initiation in a Single Crystal Superalloy under Fatigue–oxidation Conditions

Initiation of internal fatigue crack in a carbide-free bainitic steel during high cycle fatigue

Microstructural Effects in the Low-Cycle Fatigue of Fe-Ni-Cr Austenite

Micromechanisms of fatigue fracture at diffusion bonded interface of austenitic stainless steel