Abstract:It is suggested that fatigue failure mechanisms in the face-centered cubic metals are greatly affected by stacking fault energy. It was from this viewpoint that the fatigue crack initiation and stage I type crack propagation in 18-8 austenitic steel which had the lowest stacking fault energy among the face-centered cubic metals on the market, were discussed by the X-ray microbeam diffraction technique and the replica electron microscopic method.The fatigue slip line at room temperature tests has fine and straight configurations which are characteristic of low stacking fault energy materials, while the wavy and coarse slip line is typical of fatigue tests at 200°C where screw dislocation is more easily prone to cross slip. In both of these cases very complicated deformation configurations are caused by double slip and cross slip near the grain boundaries, and frequent extrusion and intrusion are observed in these areas. Fatigue crack nucleation might be caused by stress concentration at the notch and peak topography. The stage I type fatigue crack propagates immediately after the initiation, mainly along and frequently across the intense slip lines. Its growth in the area neighbouring the grain boundary runs in the direction that depends on both the crystal orientations of the grain containing the crack and the grains adjacent to it.Total misorientation and micro lattice strain measured by X-ray micro-beam diffraction technique increase abruptly at early fatigue stressing, then equilibrium values are attained and finally increase rapidly. These three periods during the fatigue deformation might be corresponding to those of the fine slip line initiation, the intensification of each slip line without new slip line formation and of final initiation of micro crack, respectively. Furthermore it will be noticed that the equilibrium value of total misorientation of 18-8 austenitic steel during the fatigue process is about one-tenth of that of carbon steel.The area of substructural zone near the fatigue crack of 18-8 austenitic steel is smaller than that of aluminum of high stacking fault energy and body-centered cubic iron. Therefore, the formations of subgrain and martensite could not be detected by X-ray micro-beam diffraction technique when irradiated by Cr-Kα of 200μφ beam size. In order to clarify these points the detailed observation at the fatigue crack tip must be made by using transmission electron microscopy. These results will be reported elsewhere.

In Situ Observation of Interfacial Fatigue Crack Growth in Diffusion Bonded Joints of Austenitic Stainless Steel

Interfacial fatigue crack growth behavior of diffusion bonded joints of 316L stainless steel

Micromechanisms of fatigue fracture at diffusion bonded interface of austenitic stainless steel

Interfacial failure mechanism of 316LSS diffusion bonded joints

Microstructure evolution and interfacial failure mechanism in 316LSS diffusion-bonded joints

Fatigue Damage of Stainless Steel Diffusion-Bonded Joints

Variation In Mechanical Properties, Microstructures And Fracture Behavior Of 304 Stainless Steel During Low-Cycle Fatigue

The low-cycle fatigue, deformation and final fracture behaviour of an austenitic stainless steel

Interface Evolution Behaviors and Shear Strength of Vacuum Diffusion Bonded 45 Steel/additive Manufactured 316L Stainless Steel Joints

Quality Evaluation of Diffusion Bonded Joints by Electrical Resistance Measuring and Microscopic Fatigue Testing

Interface Behaviors and Mechanical Properties of Diffusion Bonded 45 Steel/additive Manufactured 316L Steel Joints

Creep-fatigue Properties and Deformation Mechanism of 316L Steel Fabricated by Laser Powder Bed Fusion (PBF-LB/M)

Microstructure and Mechanical Performance of Diffusion Bonding Joints of 316L Ss with Ni Interlayer

In-situ SEM study of short fatigue crack propagation behavior in a dissimilar metal welded joint of nuclear power plant

Microstructural evolution and mechanical response of 304 stainless steel joint diffusion-bonded with micro-deformation

Study on the Influence of Surface Roughness and Temperature on the Interface Void Closure and Microstructure Evolution of Stainless Steel Diffusion Bonding Joints

Quasi-in-situ observation of fatigue crack growth behavior of friction stir welded 2024-T4 joint

Microscopic Observations of Fatigue Crack Initiation Process in 18-8 Austenitic Steel

Microcrack Initiation In Low-Cycle Fatigue Of An Austenitic Stainless Steel

Micro-mechanics investigation of heterogeneous deformation fields and crack initiation driven by the local stored energy density in austenitic stainless steel welded joints

Nonhomogeneous Microstructure Formation and Its Role on Tensile and Fatigue Performance of Duplex Stainless Steel 2205 Multi-Pass Weld Joints