Abstract:Cloud-point curves of blends of poly(methyl methacrylate) (PMMA) with a series of oligodiols based on a bisphenol A nucleus and short branches of poly(ethylene oxide) or poly(propylene oxide) (BPA-EO or BPA-PO), and with PEO and PPO oligomers, were obtained using a light transmission device. Experimental results were fitted with the Flory- Huggins model using an interaction parameter depending on both temperature and composition. For PMMA/PEO and PMMA/PPO blends, the miscibility increased when increasing the size of the diol, due to the significant decrease in the entropic and enthalpic terms contributing to the interaction parameter. This reflected the decrease in the selfassociation of solvent molecules and in the contribution of terminal OH groups to the mismatching of solubility parameters. For PMMA/BPA-EO blends, a decrease of the entropic contribution to the interaction parameter when increasing the size of the oligodiol was also found. However, the effect was counterbalanced by the opposite contribution of combinatorial terms leading to cloud-point curves located in approximately the same temperature range. For PMMA/BPA-PO blends, the interaction parameter exhibited a very low value. In this case, the effect of solvent size was much more important on combinatorial terms than on the interaction parameter, leading to an increase in miscibility when decreasing the oligodiol size. For short BPA-PO oligodiols no phase separation was observed. The entropic contribution of the interaction parameter exhibited an inverse relationship with the size of the oligodiols, independent of the nature of the chains bearing the hydroxyls and the type of OH groups (primary or secondary). This indicates that the degree of self-association of solvent molecules through their OH terminal groups, was mainly determined by their relative sizes.

Miscibility and Morphology of Ab/C-Type Blends Composed of Block-Copolymer and Homopolymer or Random Copolymer .1. Polyisoprene-Block-Poly(Methyl Methacrylate) Modified Polystyrene Blends

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

Miscibility and Morphology of AB/C‐type Blends Composed of Block Copolymer and Homopolymer or Random Coploymer, 2. Blends with Random Copolymer Effect

The Morphology and Mechanical Properties of the Hybrid Films of Styrene-Butyl Acrylate Block Copolymer/Mmt from Colloid Blending

Tuning polymer blends to cocontinuous morphology by asymmetric diblock copolymers as the surfactants

Effect of Mixing Protocol on Compatibilized Polymer Blend Morphology

Co-Continuous Polymeric Nanostructures Via Simple Melt Mixing of Ps/Pmma

Controllable Specific Interactions and Miscibility in Polymer Blends .2. A Brief Description of the Main Results

Solvent-Induced Morphology of the Binary Mixture of Diblock Copolymer in Thin Film: the Block Length and Composition Dependence of Morphology

Phase-Separation In Polymer Blends Comprising Copolymers .4. Polycarbonate Polystyrene Abcp System

Effect of the Nature of Annealing Solvent on the Morphology of Diblock Copolymer Blend Thin Films

Intermacromolecular complexation due to specific interactions: 3. Miscibility and complexation of PBMA and PS(OH)

Core-Shell Particles Of Poly(Methyl Methacrylate)-Block-Poly(N-Butyl Acrylate) Synthesized Via Reversible Addition-Fragmentation Chain-Transfer Emulsion Polymerization And The Polymer'S Application In Toughening Polycarbonate

Miscibility of blends of poly(methyl methacrylate) and oligodiols based on a bisphenol A nucleus and ethylene oxide or propylene oxide branches

Controllable Specific Interactions and Miscibility in Polymer Blends: 5. Effect of Crosslink Density in Interpenetrating Polymer Networks

Compositional Asymmetry in a Crystalline-Amorphous Block Copolymer Influences the Phase and Crystallization Behaviors of Its Blend with an Amorphous Block Copolymer

Influence of Methyl Methacrylate-Co-glycidyl Methacrylate Copolymers on the Compatibility, Morphology and Mechanical Properties of Poly(butylene Terephthalate) and Polycarbonate Blends

The Compatibility and Crystallization of the Mixtures of Poly (Tetrahydrofuran-B-methyl Methacrylate) Diblock Copolymer with Polyvinyl Chloride Homopolymer

Controllable Specific Interactions And Miscibility In Polymer Blends .4. Effect Of Hydrogen-Bonding Density In Interpenetrating Polymer Networks

The Effects of Hydrogen Bonding on the Miscibility, Complexation and Crystallization in Blends of Crystalline and Amorphous Components

Intermacromolecular complexation due to specific interactions. 6. Miscibility and complexation between Poly{Styrene-co-[p-(2-Hydroxypropan-2-yl)Styrene]}and poly[n-butyl Methacrylate-co-(4-vinylpyridine)]