Abstract:SiC fibers can be used to reinforce a range of titanium base materials including alloys of the (alpha+beta) type, metastable beta type and near a type, as well intermetallic based gamma-TiAl and orthorhombic Ti2AlNb. Along the fiber directions the obtained composites possess exceptional strength and stiffness, creating a large room and great flexibility for the design of higher performance components to be used in both aero engine and aircraft. The composites can be used by itself such as in sheet and bar form, or as a reinforcing module embedded in titanium alloy components, e.g., as a ring at the rim of a compressor disk. In this paper, recent progress in the development and application of SiC fiber reinforced titanium matrix composites was reviewed, emphasizing the work conducted at the Institute of Metal Research, Chinese Academy of Sciences. Five aspects of research were covered, the first is fiber manufacture and batch production, in which the influence of the chemical vapor deposition parameters on the quality of the W-core SiC fiber was discussed, and the relationship between the tungsten-SiC interface reaction and the high temperature stability of the fiber was described. The second part covers the composite interface, in which a detailed discussion was given to both the chemical and physical compatibility, followed by the design of different reaction layers between the SiC fiber and different titanium based matrixs. The mechanical property section presents tensile data of a range of composites developed in the authors' group and compares to literature reports where available, together with a comprehensive discussion of failure due to fatigue and creep. The fourth part deals with non-destructive testing, presenting new results of inspection on real size composite components using a combination of several techniques including X-ray, industrial CT and ultrasonic scanning. The limitations of each method were shown and the technical challenges were identified. The last part describes the development of structural parts and their verification testing. Titanium matrix composite sheets with [0/90] laminate prepared by both the foil-fiber-foil and matrix coated fiber methods were highlighted, followed by a description of the development of full size bladed ring and excess revolution testing. Future directions of research on SiC fiber reinforced titanium matrix composites were also discussed.

The Fabrication and Property of Sic Fiber Reinforced Copper Matrix Composites

Optimisation of Properties of Ti3SiC2 Reinforced Copper Matrix Composites

The Fabrication and Properties of Short Carbon Fiber Reinforced Copper Matrix Composites

Fabrication and Properties of Short Carbon Fibers Reinforced Copper Matrix Composites

Advances in Sic Fiber Reinforced Titanium Matrix Composites

Structure and properties of fine diameter continuous SiC ceramic fiber reinforced Al matrix composites

Tensile Behavior of SiC Fiber-Reinforced Γ -Tial Composites Prepared by Suction Casting

Preparation of Metal-Fiber-reinforced Al-Si-Cu Matrix Composites in a Vacuum-Suction-casting Process

Strengthening and toughening of Ti 5 Si 3 by TiC-coated short carbon fiber: Fabrication, interfacial control, and mechanism of reinforcement

Microstructure evolution and mechanical properties strengthening in laser powder bed fusion of high-strength SiC and TiB2 co-reinforced Al-Zn-Mg-Cu composites

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping

Effect of Cu Content on Microstructure and Properties of Al2o3-Sio2 Fiber Reinforced Aluminum Matrix Composites

Microstructure evolution and mechanical properties strengthening in laser powder bed fusion of high-strength SiC and TiB 2 co-reinforced Al-Zn-Mg-Cu composites

Reactions Mechanism and Mechanical Properties of a SiCf/SiC Joint Affected by Cu/Ni/Ti Elements and Inhomogeneous Composites

Interfacial Reactions and Mechanical Properties Studies of C-Coated and C/B4C Duplex-Coated SiC Fiber-Reinforced Ti2AlNb Composites

New Preparation Technology of Copper Matrix Composites Reinforced by Short Carbon Fibers

Mechanical properties of Cu/SiCp composites fabricated by composite electroforming

SiC fiber strengthened Si-14Ti high-temperature filler alloy for brazing SiCf/SiC and C/C composites

Fabrication and performance of SiC-reinforced Cu: Role of the aspect ratio of the SiC reinforcement phase

Microstructure and mechanical properties of short-carbon-fiber/Ti3SiC2 composites

Experimental Preparation of Short-Carbon-fiber-reinforced Al-5Cu Matrix Composites Using Vacuum Suction Casting