Abstract:The diamond-like carbon (DLC) coating prepared using filtered cathodic arc deposition (FCVA) lost its promising wear resistance under high temperatures. Element-doped DLC coatings have been investigated to suppress carbon oxidation reaction and subsequently enhance the wear resistance in high-temperature environments. Previous research clarified the excellent tribological properties of boron-doped DLC (B-DLC) but identified challenge such as arc discharge extinguishment and coating declamation (under high-temperature friction test). In this study, the introduction of Argon gas (10 sccm) during the deposition process stabilized stable arc discharge, resulting in high hardness and deposition rate. Moreover, a chromium interlayer and varying concentration of Cr dopant (0.5 %, 1.0 %, 3.0 % at.) were added to B-DLC to develop a stable, co-doped DLC with low friction and high wear resistance. Raman spectroscopy and nano-indentation revealed an increase in the disordered carbon structure and reduction in hardness and Young's Modulus with Cr doping. Macroscopic ball-on-disk friction test, showed 1 % Cr-doped B-DLC (a-C:B:Cr 1 ) coating exhibited super low friction (avg. coefficient 0.02) and a low specific wear rate (<5.0 × 10 −6 mm 3 /Nm). Raman spectroscopy indicated that the transferred graphite-like tribo-film onto the surface of Si 3 N 4 counterparts contributed to stable low friction. Additionally, XPS analysis on the DLC coatings' wear track suggested the rich BB bond might contribute to its high wear resistance. This successful improvement on element-doped DLC prepared by FCVA provided valuable insights for further exploration of DLC coating applied to various working situations.

Cr-doped DLC films in three mid-frequency dual-magnetron power modes

A Study of Hard Diamond-Like Carbon Films in Mid-Frequency Dual-Magnetron Sputtering

Investigation on Cr-doped Diamond-Like Carbon Films Prepared by Mid-Frequency Dual-Magnetron Sputtering

Microstructure and Mechanical Properties of Dlc Films Doped with High Crystallinity Crn Nanoparticles

Thick Diamond-like Carbon Film Deposited Using Mid-frequency Magnetron Sputtering

Investigation on Preparation and Properties of Thick DLC Film in Medium-Frequency Dual-Magnetron Sputtering

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

Influence of Cr Contents and Nanograin Sizes on Microstructure, Mechanical and Sliding Tribological Behaviors of Hard Cr-Diamond-Like Carbon Films

Microstructure and Surface Properties of Chromium-Doped Diamond-Like Carbon Thin Films Fabricated by High Power Pulsed Magnetron Sputtering

Mechanical and Tribological Properties of Diamond-Like Carbon Films Deposited by Electron Cyclotron Resonance Microwave Plasma Chemical Vapor Deposition

Influence of Three Classic Chromium-Based Transitions on the Behavior of Film/Substrate Interface in Diamond-Like Carbon Films

Influences of Interfacial Carbonization on the Structure and Mechanical Properties of Multilayered Cr-Containing Diamond-Like Carbon Films

Enhanced tribological and corrosion properties of DLC/CrN multilayer films deposited by HPPMS

Nano-Scratch Response of Diamond-Like Carbon Film Deposited by Pulsed Direct Current Magnetron Sputtering

Study on Influence of Target Powers on Properties of Diamond-Like Carbon Films Deposited by Mid-Frequency Magnetron Sputtering System

Tribological Properties of Graded Metal-doped and Nanoscale Multilayered Modulation Diamond-like Carbon Films

Tribological Behaviors of W-Doped DLC Films

The effects of Cr and B doping on the mechanical properties and tribological behavior of multi-layered hydrogenated diamond-like carbon films

Study on W Graded Doping Dlc Composite Films with Multicomponent Transition Layer

The development of B/Cr co-doped DLC coating by FCVA deposition system and its tribological properties at 300 °C

Excellent Adhered Thick Diamond-Like Carbon Coatings by Optimizing Hetero-Interfaces with Sequential Highly Energetic Cr and C Ion Treatment