Abstract:A polyoxymethylene/graphene nanocomposite is fabricated. Graphene is modified using liquid‐phase exfoliation and KH‐550. Enhanced tribomechanical behavior is achieved with 0.5 wt% graphene, ameliorated load transfer and lubricious transfer film on the interface. In this study, a viable route to the development of a high‐performance polyoxymethylene (POM)‐based nanocomposite is proposed to overcome tribomechanical‐related issues in high‐precision sliding parts. Prior to melt‐blending, graphene nanoplatelet (GNP) filler was processed via a series of liquid‐phase exfoliation and surface modification with 3‐aminopropyltriethoxysilane. Results indicate that GNP is successfully exfoliated with minimum defect ratio and improves interfacial bonding within the matrix. Uniform dispersion and stable load‐transfer capability of POM/GNP with 0.5 wt% loading significantly enhanced flexural, tensile and impact strength by overall 26.4%, in contrast to unfilled POM. Dry friction tests against a steel ball also showed the lowest reduction in friction coefficient and wear rate by 22% and 40.6%, respectively, at the same amount of GNP loading due to the large specific surface coverage and lubricious transfer film chelation onto the steel counterface. Furthermore, dissipated energy accumulation by friction work was calculated in the sliding interfaces based on friction force–displacement hysteresis loop where the POM/GNP 0.5 wt% wear surface consumed ca 21.7% less energy in a dry frictional shearing process compared to neat POM. However, lack or excess loading of processed GNP exhibited insufficient or poor matrix–filler adhesion and led to deterioration of the composite properties due to particle agglomeration which can cause stress concentration and serve as a failure site. The adoption of the proposed methodology would demonstrate excellent material characteristics in thin‐walled precision parts where both mechanical and tribological performances are the primary concern. © 2024 Society of Chemical Industry.

Development of POM Wear-resistant and Noise Damping Composite

Mechanical Properties and Friction and Wear Properties of Nano-Al_2O_3 Modified POM Nanocomposites

Preparation and Properties of Damping Materials in Multi-Phase System

EFFECT OF THE COMPOUND LUBRICANT SYSTEM ON THE TRIBOLOGICAL PROPERTIES OF POM RESIN

Mechanical and tribological properties of polyoxymethylene modified with nanoparticles and solid lubricants

Tribological Behaviour of POM Reinforced by Graphene and PTFE

Investigation on the mechanical, thermal and electrical properties of polyoxymethylene composites modified by thermoplastic polyurethane elastomer and carbon fiber

Study on the friction and wear behavior of POM/Al2O3 nanocomposites

A Pin-on-Disk Study of the Tribological Properties of Polyoxymethylene (POM) Gear Materials

Mechanical and Tribological Properties of Self-Lubricating Nanocomposites Based on POM

Physico-mechanical, thermal, and tribological studies of polytetrafluoroethylene-filled polyoxymethylene/silicone composites

Molecular dynamics study on friction of polymer material polyoxymethylene (POM)

Tribological and mechanical endowments of polyoxymethylene by liquid‐phase exfoliated graphene nanofiller

Preparation and Characterization of Silicone Oil Modified Polyurethane Damping Materials

A new polyimide matrix composite to improve friction-induced chatter performance through reducing fluctuation in friction force

Investigation on the Tribological Properties of POM Modified by Nano-PTFE

Polyimide-based composite coatings for simultaneously enhanced mechanical and tribological properties by polyhedral oligomeric silsesquioxane

Tribological properties of PTFE fiber filled polyoxymethylene composites: The influence of fiber orientation

Improving the Tribological Performance of POM through the Incorporation of Bio-Based Materials

The Development of Sustainable Polyoxymethylene (POM)-Based Composites by the Introduction of Natural Fillers and Melt Blending with Poly(lactic acid)-PLA

Modified montmorillonite synergizes with Co-MOF@PBO fabric to improve the wear resistance of PBO/phenolic resin composites