Abstract:The chemical-vapor-deposition (CVD) process is sufficiently well developed to allow the large-scale production of carbon nanotubes (CNTs). Metal nanoparticles (Fe, Co, Ni, etc.) are usually immobilized on a solid support and then decompose the gaseous hydrocarbon feedstocks into fragmented carbon units at elevated temperatures of 700-1100°C. Metal carbides are formed and then these dominate the growth of filamentous carbon as a structural template. The produced CNTs cannot stay firmly with an inert support and so inevitably detach away, especially during liquidphase purification or mechanical treatment. The biggest difficulties when handling the loose powder are filtration in the slurry-phase operations and the large pressure drops in fixed-bed reactors. These problems very much limit the application of CNTs on a large scale. The fabrication of carbon filaments on a structured support (e.g., activated carbon, carbon fibers, porous frameworks, graphite) has also suffered from discontinuities in the structure. The future use of CNTs has also been restricted by the technical requirements and the necessary high energy consumption to operate the intense and complicated CVD process. To avoid any mechanical post-treatment of powder and the risk of explosion during CVD synthesis, we have explored a simple method to produce monolithic CNTs directly as millimeter-scale spheres, featuring an integral continuity in the structure from microscopic to macroscopic scales. The whole process of CNTs growth has been conducted in a flow of ultrapure N2, involving a set of elementary steps in the solid phase being less complex than the widely used CVD process. The growth of CNTs is based on a solid reaction mechanism and well-graphitized nanotubes can be obtained even at a temperature as low as 400C. Direct observation of all growth events is made by using in-situ transmission electron microscopy (TEM), X-ray diffraction (XRD), IR, Raman spectroscopy and thermogravimetric analysis. A commercial styrene-divinylbenzene copolymer resin was used as the carbon precursor. According to Scheme 1, the ion-exchanged resin spheres were calcined at 800C in a flow of N2 or vacuum, after which the average diameter decreases from 0.77 to 0.49 mm, while the bulk density increases from 0.55 to 0.91 g ml. A novel macroscopic structure can be clearly seen, especially after the removal of the Fe nanoparticles and the amorphous carbon species by refluxing the spheres in concentrated HNO3. As seen in Fig. 1a, the twisted nanotubes construct the monolith while keeping a spherical shape. The cross-section views of the hand-broken spheres show no difference in the structure between the bulk and the surface, indicating a homogeneous distribution of the nanotubes in the millimeter-scale spheres (Fig. 1b). The nitrogen adsorption/ desorption isotherm shows a hysteresis loop to identify a typical mesoporous feature. The measured BET surface area and the pore volume are 223.7 m g and 0.42 ml g, respectively. The distribution of the pores ranges between about 2 and 15 nm.

Formation of Cus Nanotube Arrays from Cucl Nanorods Through A Gas-Solid Reaction Route

Formation Of Single-Crystalline Cus Nanoplates Vertically Standing On Flat Substrate

Growth of SiC Nanorods Prepared by Carbon Nanotubes-Confined Reaction

Novel Route to WO<i><sub>x</sub></i>Nanorods and WS<sub>2</sub>Nanotubes from WS<sub>2</sub>Inorganic Fullerenes

In-situ preparation of carbon nanotubes on CuO nanowire via chemical vapor deposition and their growth mechanism investigation

Encapsulated Nanowires Formed by Nanotube-Assisted Oriented Attachment

Preparation of Cu2S Nanoribbons from Cu(thiocarbamide)Cl·1/2H2O Complex Nanowires by Solid-state Reaction at Room Temperature Without Surfactants

From 2d Framework to Quasi-1d Nanomaterial: Preparation, Characterization, and Formation Mechanism of Cu3sns4 Nanorods

Spherical Multi-Walled Carbon-Nanotube Architectures : Formation Mechanism and Catalytic Performance

Preparation of Aligned Cu2s Nanowire Arrays and Their Field Emission Properties

Large scale synthesis of uniform CuS nanotubes in ethylene glycol by a sacrificial templating method under mild conditions

Hierarchical structures of carbon nanotubes and arrays of chromium-capped silicon nanopillars: formation and electrical properties

Diameter-Specific Growth Of Semiconducting Swnt Arrays Using Uniform Mo2c Solid Catalyst

Growth of Crystalline Cu<sub>2</sub>S Nanowire Arrays on Copper Surface: Effect of Copper Surface Structure, Reagent Gas Composition, and Reaction Temperature

Single-Crystalline γ-Ga2S3 Nanotubes via Epitaxial Conversion of GaAs Nanowires

Growth Of Sic Nanorods At Low Temperature

Lithography Inside Cu(Oh)(2) Nanorods: A General Route To Controllable Synthesis Of The Arrays Of Copper Chalcogenide Nanotubes With Double Walls

Surfactant-Assisted Growth Of Crystalline Copper Sulphide Nanowire Arrays

Tunable Self‐Assembly of Carbon Nanotubes on Silica Surface

Fabrication Of Micrometer-Scaled Hierarchical Tubular Structures Of Cus Assembled By Nanoflake-Built Microspheres Using An In Situ Formed Cu(I) Complex As A Self-Sacrificed Template

Preparation of Cu<sub>2</sub>S Dendritic, Double-Comb-Like Nanostructures by Gas-Solid Reaction Method