Abstract:Ultrafiltration hollow-fiber membranes were prepared from polyetherimide (PEI) with a wet spinning method. The effects of N,N-dimethylacetantide (DMAc) as a solvent additive in the internal coagulant and acetic acid as a non-solvent additive in the dope solution on the morphologies and performances of the membranes were investigated. The influences of PEI dope concentration on membrane morphologies and properties were also studied. Scanning electron microscopy (SEM) indicates that the addition of DMAc into the internal coagulant changes the inner fiber surface from a dense skin layer to a porous structure. However, the pure water flux of the membrane decreases with the increase of DMAc content. On the other hand, the addition of acetic acid into the casting solution promotes the spinodal demixing of the membratte-forming system and suppresses the macrovoid formation in the membrane. A nodular structure forms in the fiber skin layer. With increasing acetic acid content, the pure water flux of the membrane increases about 4-fold and the solute retention shows a slight decrease. The mechanical properties can also be improved slightly by this additive. The thermal resistance of the PEI ultrafiltration membranes prepared in this work was examined by hot water treatment at 80 degrees C. No change was observed in the permeation performance of the membranes, while the study of mechanical properties shows that the elongation-at-break of the membrane decreases slightly. PEI was sulfonated by chlorosulfonic acid (CSA) in 1,2-dichloroethane. With the increase of the molar ratio of CSA to PEI repeat unit and/or reaction time, the ion-exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increases accordingly. Water uptake test and contact angle measurements show that the hydrophillicity of the SPEI increases with the increase of the IEC. Polyetherimide/sulfonated polyetherintide (PEI/SPET) ultrafiltration hollow-fiber membranes were also prepared with a dry-wet phase inversion method and SPEI was used as a polymer additive. SEM study reveals that the addition of SPEI induces the formation of nodular structure and suppresses the formation of finger-like macrovoids. With the increase of air-gap distance, it was found that the number of micropores formed in the outer fiber surface and the pore size increased. On the other hand, the pure water flux of the membrane reaches a maximum and then decreases, while the solute retention decreases at first and then levels off at longer air-gap. Based on the filtration of bovine serum albuntin (BSA) solution, it was found that the use of SPEI in the blend membranes increased their hydrophilicity.

Effect of polyvinylpyrrolidone on the morphology and properties of polyetherimide ultra-filtration membranes

Modification of Porous Poly(Vinylidene Fluoride) Membrane Using Amphiphilic Polymers with Different Structures in Phase Inversion Process

Improving Hydrophilicity And Protein Resistance Of Poly(Vinylidene Fluoride) Membranes By Blending With Amphiphilic Hyperbranched-Star Polymer

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Study on polyetherimide hollow fiber ultrafiltration membrane (Ⅰ) Membrane structure, thermal and mechanical properties

Effect of Polyvinylpyrrolidone Molecular Weights on Morphology, Oil/Water Separation, Mechanical and Thermal Properties of Polyetherimide/Polyvinylpyrrolidone Hollow Fiber Membranes

Preparation of poly (vinyl butyral) hollow fiber ultrafiltration membrane via wet-spinning method using PVP as additive

Preparation And Performance Of Ultrafiltration Membranes From Polyetherimide And Its Sulfonated Derivatives

Morphology and Performance of Polyvinylidene Fluoride/Perfluorosulphonic Acid Hollow Fibre Ultrafiltration Blend Membranes

Ultrafiltration Hollow Fiber Membranes from Poly(Ether Imide): Preparation, Morphologies and Properties

Preparation and Characterization of PVDF-PFSA Flat Sheet Ultrafiltration Membranes

Effect of PEG Additives on Properties and Morphologies of Polyetherimide Membranes Prepared by Phase Inversion

Effects of Pore-Forming Additives on Structures and Properties of Pvdf/Fe3+/Cu2+ Hollow Fiber Membranes

Separation performance enhancement of PEEKWC/PEI cross-linked ultrafiltration membranes by poly(ethylene glycol) and polyvinylpyrrolidone as polymeric additives

Enhanced Permeability and Fouling-Resistant Capacity of Poly(vinylidene Fluoride) Ultrafiltration Membrane Based on the PPG-co-PEG-co-PPG Copolymer with Two Hydrophobic Terminals and One Hydrophilic Intermediate.

Analysis of Additives on Hydrophilic Properties and Filtration Properties of Polysulfone Ultrafiltration Membrane

Exploring the Synergetic Effects of Graphene Oxide (go) and Polyvinylpyrrodione (pvp) on Poly(Vinylylidenefluoride) (pvdf) Ultrafiltration Membrane Performance

Surface Free Energy, Microstructure and Performance of Polyvinylidene Fluoride (PVDF) Membrane: the Influence of Hydrophilic Porogens

Ultrafiltration membranes prepared from polyethersulfone-grafted-poly (N-vinyl-pyrrolidone) synthesized via simultaneous irradiation in homogenous phase and their anti-fouling performance

Improved Antifouling Property of Poly(Ether Sulfone) Ultrafiltration Membrane Through Blending with Poly(Vinyl Alcohol)

Poly(vinyl chloride) (PVC) hollow fiber ultrafiltration membranes prepared from PVC/additives/solvent